2010 Infiniti FX - SRS Airbag Control System (Section SRC) (173 pages)
Download SRS Airbag Control System (Section SRC)
Manual Description
DIAGNOSIS AND REPAIR WORK FLOW 5, cONTROL UNIT : Special Repair Requirement 8, zERO POINT RESET : Description 8, zERO POINT RESET : Special Repair Requirement 8.
B1004, B1005 DIAGNOSIS SENSOR UNIT 23, b1014, B1015 DIAGNOSIS SENSOR UNIT 27, air Bag Warning Lamp Diagnosis 16, pASS A/B INDCTR CKT 35.
Wiring Diagram - SRS AIR BAG CONTROL SYSTEM - 161, sRS AIR BAG WARNING LAMP DOES NOT, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 173, dIAGNOSIS AND REPAIR WORK FLOW.
Interview the customer for the symptom (the condition and the environment when incident/malfunction, check the symptom customer information, check air bag warning lamp operation in the user mode, check self diagnostic result with CONSULT-III diagnosis mode.
Perform the following procedure DTC detected, record DTC (Print them out with CONSULT-III, study the relationship between the malfunction that DTC or air bag warning lamp indicates symptom, check related service bulletins information.
Perform DTC CONFIRMATION PROCEDURE DTC, perform Diagnosis Procedure for the air bag warning lamp operation, inspect according to Diagnostic Procedure DTC, repair or replace malfunctioning part.
Check self diagnostic result and air bag warning lamp operation user mode, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description, when replacing or removing and installing passenger seat, always perform zero point reset so that Occupant.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement, wORK PROCEDURE WHEN REPLACING CONTROL UNIT, is zero point reset performed normally, >> Check condition as per the following, and perform zero point reset again.
Passenger seat is occupied by an object, excessive vibration is applied while performing zero point reset, if Incomplete” is displayed on zero point reset current status”, zero point reset not completed, zero point reset is an initializing procedure for occupant detection sensor that must be performed when replacing or removing installing passenger seat.
If zero point reset is not performed, the initialization is incomplete and Occupant Detection System does not, when zero point reset is performed once after removal and installation of passenger seat, CONSULT-III displays complete”, when reinstalling passenger seat after removal, the initial value for occupant detection sensor changes, occupant Detection System does not operate normally.
Always perform zero point reset after performing the work per following, - Installation of passenger seat that is zero point reset complete, zERO POINT RESET : Special Repair Requirement, when performing zero point reset, be careful of the items described per following.
Perform zero point reset after installing passenger seat vehicle, do not apply excessive vibration vehicle, select start on Zero point reset function” screen from, WORK SUPPORT CONSULT-III OCCUPANT, proceed to Zero point reset function” screen from work support CONSULT-III OCCUPANT DETECTION”.
Complete” is displayed on zero point reset current status” if the seat is reinstalled by seat removal, and installation, or zero point reset” already performed, zero point reset current status” displays Incomplete” if a new seat is installed, switch ON without performing zero point reset, front passenger air bag OFF indicator turns ON.
When zero point reset is performed, front passenger air bag OFF indicator turns OFF, air bag warning lamp blinks user mode only, air bag sensor unit does not record whether or not zero point reset performed.
Manual Description
DIAGNOSIS AND REPAIR WORK FLOW 5, cONTROL UNIT : Special Repair Requirement 8, zERO POINT RESET : Description 8, zERO POINT RESET : Special Repair Requirement 8.
B1004, B1005 DIAGNOSIS SENSOR UNIT 23, b1014, B1015 DIAGNOSIS SENSOR UNIT 27, air Bag Warning Lamp Diagnosis 16, pASS A/B INDCTR CKT 35.
Wiring Diagram - SRS AIR BAG CONTROL SYSTEM - 161, sRS AIR BAG WARNING LAMP DOES NOT, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 173, dIAGNOSIS AND REPAIR WORK FLOW.
Interview the customer for the symptom (the condition and the environment when incident/malfunction, check the symptom customer information, check air bag warning lamp operation in the user mode, check self diagnostic result with CONSULT-III diagnosis mode.
Perform the following procedure DTC detected, record DTC (Print them out with CONSULT-III, study the relationship between the malfunction that DTC or air bag warning lamp indicates symptom, check related service bulletins information.
Perform DTC CONFIRMATION PROCEDURE DTC, perform Diagnosis Procedure for the air bag warning lamp operation, inspect according to Diagnostic Procedure DTC, repair or replace malfunctioning part.
Check self diagnostic result and air bag warning lamp operation user mode, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description, when replacing or removing and installing passenger seat, always perform zero point reset so that Occupant.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement, wORK PROCEDURE WHEN REPLACING CONTROL UNIT, is zero point reset performed normally, >> Check condition as per the following, and perform zero point reset again.
Passenger seat is occupied by an object, excessive vibration is applied while performing zero point reset, if Incomplete” is displayed on zero point reset current status”, zero point reset not completed, zero point reset is an initializing procedure for occupant detection sensor that must be performed when replacing or removing installing passenger seat.
If zero point reset is not performed, the initialization is incomplete and Occupant Detection System does not, when zero point reset is performed once after removal and installation of passenger seat, CONSULT-III displays complete”, when reinstalling passenger seat after removal, the initial value for occupant detection sensor changes, occupant Detection System does not operate normally.
Always perform zero point reset after performing the work per following, - Installation of passenger seat that is zero point reset complete, zERO POINT RESET : Special Repair Requirement, when performing zero point reset, be careful of the items described per following.
Perform zero point reset after installing passenger seat vehicle, do not apply excessive vibration vehicle, select start on Zero point reset function” screen from, WORK SUPPORT CONSULT-III OCCUPANT, proceed to Zero point reset function” screen from work support CONSULT-III OCCUPANT DETECTION”.
Complete” is displayed on zero point reset current status” if the seat is reinstalled by seat removal, and installation, or zero point reset” already performed, zero point reset current status” displays Incomplete” if a new seat is installed, switch ON without performing zero point reset, front passenger air bag OFF indicator turns ON.
When zero point reset is performed, front passenger air bag OFF indicator turns OFF, air bag warning lamp blinks user mode only, air bag sensor unit does not record whether or not zero point reset performed.
Read(view) online free pdf manual 2010 Infiniti FX
Infiniti Models