2010 Infiniti FX - Driveline (Section DLN) (294 pages)
Download Driveline (Section DLN)
Manual Description
DIAGNOSIS AND REPAIR WORK FLOW 7, cONSULT-III Function (ALL MODE AWD/4WD) 12, pOWER SUPPLY AND GROUND CIRCUIT 27, wiring Diagram - AWD SYSTEM - 34.
AWD WARNING LAMP DOES NOT TURN ON, aWD WARNING LAMP DOES NOT TURN, hEAVY TIGHT-CORNER BRAKING SYMPTOM OCCURS 44, vEHICLE DOES NOT ENTER AWD MODE 45.
AWD WARNING LAMP BLINKS SLOWLY 47, aWD WARNING LAMP BLINKS QUICKLY 46, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 49, precaution Necessary for Steering Wheel Rotation after Battery Disconnect 49.
Service Notice or Precautions Transfer 50, : Special Service Tools 51, : Commercial Service Tools 52, : Special Service Tools 53.
: Commercial Service Tools 54, fRONT CASE AND REAR CASE 69, fRONT DRIVE SHAFT AND DRIVE CHAIN97, precaution Necessary for Steering Wheel Rotation after Battery Disconnect 142.
Service Notice or Precautions Front Final Drive, rIGHT SIDE : Exploded View 147, rIGHT SIDE : Removal Installation 148, lEFT SIDE : Exploded View 148.
LEFT SIDE : Removal Installation 149, aWD : Removal Installation 205, aWD : Removal Installation 209, : Inspection After Disassembly 223.
AWD : Inspection After Disassembly 236, service Notice or Precautions for Rear Final Drive 187, aWD : Removal Installation 198, : Inspection After Disassembly 245.
AWD : Inspection After Disassembly 254, service Notice or Precautions for Rear Final Drive 260, dIAGNOSIS AND REPAIR WORK FLOW, ask customer about his/her complaints carefully.
Maybe the customer mentions symptom”, start the engine and drive at 30 km/h (19 MPH) or more approximately 1 minute, does AWD warning lamp turn ON, perform self-diagnosis ALL MODE AWD/4WD”.
Erase self-diagnostic results ALL MODE AWD/4WD”, check pin terminals for damage or loose connection with harness connector, perform DTC reproduction procedure error system, perform the symptom diagnosis each system.
Check input/output signal standard ALL MODE AWD/4WD”, is the input/output standard value, electronic control allows optimal distribution of torque to front/rear wheels match road conditions, makes possible stable driving, with no wheel spin, on snowy roads other slippery surfaces.
On roads which do not require AWD, it contributes to improved fuel economy by driving conditions close, sensor inputs determine the vehicle's turning condition, and in response tight cornering/braking are controlled by distributing optimum torque front wheels, it transmits/receives each signal from the following control unit via CAN communication line, aBS actuator and electric unit (control unit).
Transmits the following signals via CAN communication AWD control unit, stop lamp switch signal (brake signal), transmits conditions of parking brake switch via CAN communication AWD control.
Manual Description
DIAGNOSIS AND REPAIR WORK FLOW 7, cONSULT-III Function (ALL MODE AWD/4WD) 12, pOWER SUPPLY AND GROUND CIRCUIT 27, wiring Diagram - AWD SYSTEM - 34.
AWD WARNING LAMP DOES NOT TURN ON, aWD WARNING LAMP DOES NOT TURN, hEAVY TIGHT-CORNER BRAKING SYMPTOM OCCURS 44, vEHICLE DOES NOT ENTER AWD MODE 45.
AWD WARNING LAMP BLINKS SLOWLY 47, aWD WARNING LAMP BLINKS QUICKLY 46, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 49, precaution Necessary for Steering Wheel Rotation after Battery Disconnect 49.
Service Notice or Precautions Transfer 50, : Special Service Tools 51, : Commercial Service Tools 52, : Special Service Tools 53.
: Commercial Service Tools 54, fRONT CASE AND REAR CASE 69, fRONT DRIVE SHAFT AND DRIVE CHAIN97, precaution Necessary for Steering Wheel Rotation after Battery Disconnect 142.
Service Notice or Precautions Front Final Drive, rIGHT SIDE : Exploded View 147, rIGHT SIDE : Removal Installation 148, lEFT SIDE : Exploded View 148.
LEFT SIDE : Removal Installation 149, aWD : Removal Installation 205, aWD : Removal Installation 209, : Inspection After Disassembly 223.
AWD : Inspection After Disassembly 236, service Notice or Precautions for Rear Final Drive 187, aWD : Removal Installation 198, : Inspection After Disassembly 245.
AWD : Inspection After Disassembly 254, service Notice or Precautions for Rear Final Drive 260, dIAGNOSIS AND REPAIR WORK FLOW, ask customer about his/her complaints carefully.
Maybe the customer mentions symptom”, start the engine and drive at 30 km/h (19 MPH) or more approximately 1 minute, does AWD warning lamp turn ON, perform self-diagnosis ALL MODE AWD/4WD”.
Erase self-diagnostic results ALL MODE AWD/4WD”, check pin terminals for damage or loose connection with harness connector, perform DTC reproduction procedure error system, perform the symptom diagnosis each system.
Check input/output signal standard ALL MODE AWD/4WD”, is the input/output standard value, electronic control allows optimal distribution of torque to front/rear wheels match road conditions, makes possible stable driving, with no wheel spin, on snowy roads other slippery surfaces.
On roads which do not require AWD, it contributes to improved fuel economy by driving conditions close, sensor inputs determine the vehicle's turning condition, and in response tight cornering/braking are controlled by distributing optimum torque front wheels, it transmits/receives each signal from the following control unit via CAN communication line, aBS actuator and electric unit (control unit).
Transmits the following signals via CAN communication AWD control unit, stop lamp switch signal (brake signal), transmits conditions of parking brake switch via CAN communication AWD control.
Read(view) online free pdf manual 2010 Infiniti FX
Infiniti Models