2010 Infiniti FX - Body Repair (Section BRM) (58 pages)
Download Body Repair (Section BRM)
Manual Description
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY, when repairing and painting a portion of the body adjacent to plastic parts, consider their characteristics, (influence of heat and solvent) and remove them if necessary or take suitable measures protect them, plastic parts should be repaired and painted using methods suiting materials, characteristics.
Side radiator core support assembly 2, front strut housing (RH & LH), lower rear hoodledge (RH & LH), upper front hoodledge (RH & LH).
Upper rear hoodledge (RH & LH), upper side cowl top (RH & LH), : Both sided anti-corrosive precoated steel sections, : High strength steel (HSS) sections.
: Both sided anti-corrosive steel HSS sections, for the parts without a number described in the figure, it is supplied only with the assembly part that the part included with, side body assembly (RH & LH), outer front side body (RH & LH).
Front pillar brace (RH & LH), outer sill reinforcement (RH & LH), inner roof rail reinforcement (RH &, to provide improved corrosion prevention, the following anti-corrosive measures have been implemented.
To improve repairability and corrosion resistance, a new type of anticorrosive precoated steel sheet adopted replacing conventional, galvannealed steel is electroplated and heated form Zinc-iron, alloy, which provides excellent and long term corrosion resistance, nISSAN genuine parts are fabricated from galvannealed steel.
Genuine parts or an equivalent be used for panel replacement to maintain anti-corrosive performance built, phosphate Coating Treatment Cationic Electrodeposition Primer, a phosphate coating treatment cationic electrodeposition, primer, which provide excellent corrosion protection, applied.
Confine paint removal during welding operation an absolute, nISSAN genuine parts are also treated in the same manner, the underside of the floor and wheelhouse are undercoated to prevent rust, vibration, noise and stone chipping, do not apply undercoating to any place unless specified (such as the areas above muffler three.
Way catalyst which subjected heat), do not undercoat the exhaust pipe or other parts which become hot, apply bitumen wax after applying undercoating, after putting seal on the vehicle, put undercoating it.
The following figure shows the areas that are sealed at the factory, should be smooth and free from cuts or gaps, and not to allow other unaffected parts to come into contact with sealant, a mark is placed on each part of the body to indicate the vehicle center.
These marks together with body alignment specifications, all dimensions indicated in figures actual, when using a tracking gauge, adjust both pointers to equal length, to make sure there no free play.
When a measuring tape is used, check to be sure there is no elongation, twisting bending, measurements should be taken at the center mounting holes, an asterisk (*) following the value at the measuring point indicates that the measuring point other side, ″Z″: Imaginary base line [200 mm (7.
Dimensions marked with ″*″ indicate symmetrically identical dimensions on both the right and left hand, upper dash positioning mark center positioning mark, radiator core support hole center φ7 (0, hood hinge installing hole center φ9 (0.
Radiator core support stay hole center φ12 (0, front fender installing hole center φ7 (0, front side member hole center φ10 (0.
Manual Description
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY, when repairing and painting a portion of the body adjacent to plastic parts, consider their characteristics, (influence of heat and solvent) and remove them if necessary or take suitable measures protect them, plastic parts should be repaired and painted using methods suiting materials, characteristics.
Side radiator core support assembly 2, front strut housing (RH & LH), lower rear hoodledge (RH & LH), upper front hoodledge (RH & LH).
Upper rear hoodledge (RH & LH), upper side cowl top (RH & LH), : Both sided anti-corrosive precoated steel sections, : High strength steel (HSS) sections.
: Both sided anti-corrosive steel HSS sections, for the parts without a number described in the figure, it is supplied only with the assembly part that the part included with, side body assembly (RH & LH), outer front side body (RH & LH).
Front pillar brace (RH & LH), outer sill reinforcement (RH & LH), inner roof rail reinforcement (RH &, to provide improved corrosion prevention, the following anti-corrosive measures have been implemented.
To improve repairability and corrosion resistance, a new type of anticorrosive precoated steel sheet adopted replacing conventional, galvannealed steel is electroplated and heated form Zinc-iron, alloy, which provides excellent and long term corrosion resistance, nISSAN genuine parts are fabricated from galvannealed steel.
Genuine parts or an equivalent be used for panel replacement to maintain anti-corrosive performance built, phosphate Coating Treatment Cationic Electrodeposition Primer, a phosphate coating treatment cationic electrodeposition, primer, which provide excellent corrosion protection, applied.
Confine paint removal during welding operation an absolute, nISSAN genuine parts are also treated in the same manner, the underside of the floor and wheelhouse are undercoated to prevent rust, vibration, noise and stone chipping, do not apply undercoating to any place unless specified (such as the areas above muffler three.
Way catalyst which subjected heat), do not undercoat the exhaust pipe or other parts which become hot, apply bitumen wax after applying undercoating, after putting seal on the vehicle, put undercoating it.
The following figure shows the areas that are sealed at the factory, should be smooth and free from cuts or gaps, and not to allow other unaffected parts to come into contact with sealant, a mark is placed on each part of the body to indicate the vehicle center.
These marks together with body alignment specifications, all dimensions indicated in figures actual, when using a tracking gauge, adjust both pointers to equal length, to make sure there no free play.
When a measuring tape is used, check to be sure there is no elongation, twisting bending, measurements should be taken at the center mounting holes, an asterisk (*) following the value at the measuring point indicates that the measuring point other side, ″Z″: Imaginary base line [200 mm (7.
Dimensions marked with ″*″ indicate symmetrically identical dimensions on both the right and left hand, upper dash positioning mark center positioning mark, radiator core support hole center φ7 (0, hood hinge installing hole center φ9 (0.
Radiator core support stay hole center φ12 (0, front fender installing hole center φ7 (0, front side member hole center φ10 (0.
Read(view) online free pdf manual 2010 Infiniti FX
Infiniti Models