2009 Toyota Venza - Operating the lights and wipers (16 pages)
Download Operating the lights and wipers
Manual Description
The headlights can be operated manually automatically, the side marker, parking, tail, license plate, position [vehicles without smart key system], turning on high beam headlights.
High Beam system will be activated, pull the lever toward you, release the lever turn them off, you can flash high beams.
Pull the lever back center, position to turn high beams, to make your vehicle more visible to other drivers, headlights turn, automatically (at a reduced intensity) whenever the engine started.
The sensor may not function properly, an object is placed on the sensor, or anything that blocks the sensor affixed, doing so interferes with sensor, detecting the level ambient light.
May cause the automatic headlight system malfunction, ● When the headlights are on: The headlights and tail lights turn off 30, seconds after a door is opened and closed ENGINE START, sTOP” switch has been switched to ACCESSORY OFF mode.
● When only the tail lights are on: The tail lights turn off automatically, the ENGINE START STOP” switch is switched ACCESSORY, oFF mode and driver's door opened, seconds after a door is opened and closed if engine switch has.
Been switched to ACC” LOCK” position, the engine switch is switched to ACC” or LOCK” position driver's, to turn the lights on again, turn the engine switch to ON” position, turn the light switch off once and then back.
Automatic headlight leveling system (Vehicles with discharge headlights), the level of the headlights is automatically adjusted according number, of passengers and the loading condition of the vehicle ensure that, headlights do not interfere with other road users.
To turn the lights on again, turn the ENGINE START STOP” switch, iGNITION ON mode, or turn the light switch off once and then back, indicator flashes (Vehicles with discharge headlights), it may indicate a malfunction in the system.
Customization that can be configured at Toyota dealer by TFT, do not leave the lights on longer than necessary when the engine not running, automatic High Beam (vehicles with discharge headlights), the Automatic High Beam uses an in-vehicle camera sensor.
Assess the brightness of streetlights, the lights oncoming, activating the Automatic High Beam system, the Automatic High Beam indicator will come when, headlights are turned on automatically indicate that.
Push the lever away you, is in the ON” position (vehicles without smart key system), turning the high beam on/off manually, pull the lever original position.
High beam automatic turning off conditions, when all of the following conditions are fulfilled, high beam will be, automatically turned on (after approximately 1 second), ● Vehicle speed is above approximately 20 mph (32 km/h).
● The area ahead of vehicle dark, ● There are no oncoming or preceding vehicles with headlights, ● Vehicle speed drops below approximately 20 mph (32 km/h).
Manual Description
The headlights can be operated manually automatically, the side marker, parking, tail, license plate, position [vehicles without smart key system], turning on high beam headlights.
High Beam system will be activated, pull the lever toward you, release the lever turn them off, you can flash high beams.
Pull the lever back center, position to turn high beams, to make your vehicle more visible to other drivers, headlights turn, automatically (at a reduced intensity) whenever the engine started.
The sensor may not function properly, an object is placed on the sensor, or anything that blocks the sensor affixed, doing so interferes with sensor, detecting the level ambient light.
May cause the automatic headlight system malfunction, ● When the headlights are on: The headlights and tail lights turn off 30, seconds after a door is opened and closed ENGINE START, sTOP” switch has been switched to ACCESSORY OFF mode.
● When only the tail lights are on: The tail lights turn off automatically, the ENGINE START STOP” switch is switched ACCESSORY, oFF mode and driver's door opened, seconds after a door is opened and closed if engine switch has.
Been switched to ACC” LOCK” position, the engine switch is switched to ACC” or LOCK” position driver's, to turn the lights on again, turn the engine switch to ON” position, turn the light switch off once and then back.
Automatic headlight leveling system (Vehicles with discharge headlights), the level of the headlights is automatically adjusted according number, of passengers and the loading condition of the vehicle ensure that, headlights do not interfere with other road users.
To turn the lights on again, turn the ENGINE START STOP” switch, iGNITION ON mode, or turn the light switch off once and then back, indicator flashes (Vehicles with discharge headlights), it may indicate a malfunction in the system.
Customization that can be configured at Toyota dealer by TFT, do not leave the lights on longer than necessary when the engine not running, automatic High Beam (vehicles with discharge headlights), the Automatic High Beam uses an in-vehicle camera sensor.
Assess the brightness of streetlights, the lights oncoming, activating the Automatic High Beam system, the Automatic High Beam indicator will come when, headlights are turned on automatically indicate that.
Push the lever away you, is in the ON” position (vehicles without smart key system), turning the high beam on/off manually, pull the lever original position.
High beam automatic turning off conditions, when all of the following conditions are fulfilled, high beam will be, automatically turned on (after approximately 1 second), ● Vehicle speed is above approximately 20 mph (32 km/h).
● The area ahead of vehicle dark, ● There are no oncoming or preceding vehicles with headlights, ● Vehicle speed drops below approximately 20 mph (32 km/h).
Toyota Models