2000 Toyota Land Cruiser - Engine and Chassis (12 pages)
Download Engine and Chassis
Manual Description
Checking the engine oil level 232, checking the engine coolant level 234, installing snow tires chains 239, be careful not to touch hot exhaust manifold.
Above the low level, add engine oil, the same type as already engine, with the engine at operating temperature and turned off, check oil level, should be on a level spot.
Off the engine, wait few minutes, the oil to drain back into bottom, vehicle, reinsert the dipstick in the direction so that ”ENGINE OIL”, top should be read correctly push.
The approximate quantity oil needed, fill between the low level full level, on the dipstick is indicated below reference, when the level reaches within correct.
Range, install filler cap hand−tight, remove the oil filler cap add engine, oil in small quantities time, checking, z Check the oil level dipstick.
Once again after adding oil, multigrade engine oil ILSAC multigrade, sAE is the best choice your, vehicle, for good fuel economy.
May become difficult start, so SAE, either or both API registered marks, added to some oil containers help, the API Service Symbol is located anywhere on the outside container.
Quality by API (American Petroleum Institute) designations such SJ, portion of the label shows the SAE viscosity grade such SAE 5W−30, indicates that the oil has fuel−saving capabilities, the ILSAC (International Lubricant Standardization and Approval Committee) Certification Mark is displayed front.
Look at the see−through coolant reservoir when the engine is cold, the ”FULL” and ”LOW” lines, the coolant level in reservoir will vary, level is on or below ”LOW” line, add.
For a proper corrosion protection of aluminum components, if the coolant level drops within short, time after replenishing, there may be, radiator, hoses, radiator cap drain.
Dealer test the cap pressure check, to prevent burning yourself, do not, remove the radiator cap when engine hot, use of improper coolants may damage.
For a proper corrosion protection your, in addition to preventing freezing and subsequent damage to engine, type, read the coolant container information, of the cooling system given Section.
Your Toyota, to provide protection down, about 60% solution is recommended, if the level is low, add SAE J1703, add brake fluid up ”MAX” line.
To check the fluid level, simply look, down slightly as the brake pads wear, when the fluid level accumulator.
Manual Description
Checking the engine oil level 232, checking the engine coolant level 234, installing snow tires chains 239, be careful not to touch hot exhaust manifold.
Above the low level, add engine oil, the same type as already engine, with the engine at operating temperature and turned off, check oil level, should be on a level spot.
Off the engine, wait few minutes, the oil to drain back into bottom, vehicle, reinsert the dipstick in the direction so that ”ENGINE OIL”, top should be read correctly push.
The approximate quantity oil needed, fill between the low level full level, on the dipstick is indicated below reference, when the level reaches within correct.
Range, install filler cap hand−tight, remove the oil filler cap add engine, oil in small quantities time, checking, z Check the oil level dipstick.
Once again after adding oil, multigrade engine oil ILSAC multigrade, sAE is the best choice your, vehicle, for good fuel economy.
May become difficult start, so SAE, either or both API registered marks, added to some oil containers help, the API Service Symbol is located anywhere on the outside container.
Quality by API (American Petroleum Institute) designations such SJ, portion of the label shows the SAE viscosity grade such SAE 5W−30, indicates that the oil has fuel−saving capabilities, the ILSAC (International Lubricant Standardization and Approval Committee) Certification Mark is displayed front.
Look at the see−through coolant reservoir when the engine is cold, the ”FULL” and ”LOW” lines, the coolant level in reservoir will vary, level is on or below ”LOW” line, add.
For a proper corrosion protection of aluminum components, if the coolant level drops within short, time after replenishing, there may be, radiator, hoses, radiator cap drain.
Dealer test the cap pressure check, to prevent burning yourself, do not, remove the radiator cap when engine hot, use of improper coolants may damage.
For a proper corrosion protection your, in addition to preventing freezing and subsequent damage to engine, type, read the coolant container information, of the cooling system given Section.
Your Toyota, to provide protection down, about 60% solution is recommended, if the level is low, add SAE J1703, add brake fluid up ”MAX” line.
To check the fluid level, simply look, down slightly as the brake pads wear, when the fluid level accumulator.
Toyota Models