2002 Toyota Camry - Engine and Chassis (12 pages)
Download Engine and Chassis
Manual Description
AP Camry U (L/O 0201), with the engine at operating temperature and turned off, check oil level, should be on a level spot, off the engine, wait few minutes.
The oil to drain back into bottom, be careful not to touch hot exhaust manifold, above the low level line, add engine oil, of the same type as already engine.
SL Energy−Conserving” or ILSAC multigrade engine oil, remove the oil filler cap add engine, oil in small quantities time, checking, the approximate quantity oil needed.
Fill between the low level full level, on the dipstick is indicated below reference, when the level reaches within correct, range, install filler cap hand−tight.
SAE is the best choice your, vehicle, for good fuel economy, may become difficult start, so SAE, z Check the oil level dipstick.
Once again after adding oil, either or both API registered marks, added to some oil containers help, the API Service Symbol is located anywhere on the outside container.
Quality by API (American Petroleum Institute) designations such SL, portion of the label shows the SAE viscosity grade such SAE 5W−30, indicates that the oil has fuel−saving capabilities, the ILSAC (International Lubricant Standardization and Approval Committee) Certification Mark is displayed front.
Look at the see−through coolant reservoir when the engine is cold, the F” and L” lines reservoir, if the level low, add ethylene−glycol, the coolant level in reservoir will vary.
Level is on or below L” line, add, for a proper corrosion protection of aluminum components, if the coolant level drops within short, time after replenishing, there may be.
Radiator, hoses, engine coolant filler cap, radiator cap and drain cock water, dealer test the cap pressure check, to prevent burning yourself, do not.
Remove the radiator cap when engine hot, use of improper coolants may damage, for a proper corrosion protection your, your Toyota, to provide protection down.
About C (−58 F), 60% solution is recommended, to prevent yourself burning, be, careful not to touch radiator, and condenser, do not perform.
Type of coolant will also prevent corrosion, read the coolant container information, of the cooling system given page, if the level is low, add SAE J1703.
Remove and replace reservoir cap by, level when you put cap back on, use only newly opened brake fluid.
Manual Description
AP Camry U (L/O 0201), with the engine at operating temperature and turned off, check oil level, should be on a level spot, off the engine, wait few minutes.
The oil to drain back into bottom, be careful not to touch hot exhaust manifold, above the low level line, add engine oil, of the same type as already engine.
SL Energy−Conserving” or ILSAC multigrade engine oil, remove the oil filler cap add engine, oil in small quantities time, checking, the approximate quantity oil needed.
Fill between the low level full level, on the dipstick is indicated below reference, when the level reaches within correct, range, install filler cap hand−tight.
SAE is the best choice your, vehicle, for good fuel economy, may become difficult start, so SAE, z Check the oil level dipstick.
Once again after adding oil, either or both API registered marks, added to some oil containers help, the API Service Symbol is located anywhere on the outside container.
Quality by API (American Petroleum Institute) designations such SL, portion of the label shows the SAE viscosity grade such SAE 5W−30, indicates that the oil has fuel−saving capabilities, the ILSAC (International Lubricant Standardization and Approval Committee) Certification Mark is displayed front.
Look at the see−through coolant reservoir when the engine is cold, the F” and L” lines reservoir, if the level low, add ethylene−glycol, the coolant level in reservoir will vary.
Level is on or below L” line, add, for a proper corrosion protection of aluminum components, if the coolant level drops within short, time after replenishing, there may be.
Radiator, hoses, engine coolant filler cap, radiator cap and drain cock water, dealer test the cap pressure check, to prevent burning yourself, do not.
Remove the radiator cap when engine hot, use of improper coolants may damage, for a proper corrosion protection your, your Toyota, to provide protection down.
About C (−58 F), 60% solution is recommended, to prevent yourself burning, be, careful not to touch radiator, and condenser, do not perform.
Type of coolant will also prevent corrosion, read the coolant container information, of the cooling system given page, if the level is low, add SAE J1703.
Remove and replace reservoir cap by, level when you put cap back on, use only newly opened brake fluid.
Toyota Models