2003 Nissan Xterra - Wiper Washer (Section WW) (16 pages)
Download Wiper Washer (Section WW)
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 2, wiring Diagrams Trouble Diagnosis 2, wiring Diagram — WIPER — 5, wiring Diagram — WIP/R — 10.
Wiring Diagram — CIGAR — 14, wiring Diagram — HORN — 15, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, when you read wiring diagrams, refer following.
When you perform trouble diagnosis, refer following, "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES", "How to Perform Efficient Diagnosis an Electrical Incident", check for any Service bulletins before servicing vehicle.
The front wiper switch is controlled by a lever built into combination switch, there are two front wiper switch positions, with the ignition switch in the ON or START position, power supplied, to front wiper motor terminal B.
Low and High Speed Wiper Operation, ground is supplied to front wiper switch terminal 17 through body grounds E12 E54, with the front wiper switch in the LO position, ground supplied, to front wiper motor terminal L.
Through front wiper switch terminal 14, with power and ground supplied, the front wiper motor operates low speed, with the front wiper switch in the HI position, ground supplied, to front wiper motor terminal H.
Through front wiper switch terminal 16, with power and ground supplied, the front wiper motor operates high speed, when the front wiper switch is turned OFF, the front wiper motor will continue to operate low speed until, when wiper blades are not located at base of windshield with front wiper switch OFF, ground supplied.
Through front wiper switch terminal 13, through front wiper motor terminal P, through front wiper motor terminal E, through body grounds E12 E54.
There are three front wiper switch positions, to front wiper switch terminal 19, when wiper blades reach base of windshield, front wiper motor terminals B and P connected instead, to front wiper switch terminal 13.
With battery voltage supplied to front wiper switch terminal 13, the front wiper switch will stop front wiper, motor with the wiper blades PARK position, the wiper blades perform a single wiping operation, followed by a delay interval which adjustable, approximately to 13 seconds, after which the cycle repeats.
When the front wiper switch is placed in the INT position, ground supplied intermittently, through front wiper switch terminal 17, the delay interval time is controlled by wiper switch, the wiper motor operates at low speed at desired delay interval.
To front washer motor terminal +, when the lever is pulled to the WASH position, ground supplied, to front washer motor terminal –.
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 2, wiring Diagrams Trouble Diagnosis 2, wiring Diagram — WIPER — 5, wiring Diagram — WIP/R — 10.
Wiring Diagram — CIGAR — 14, wiring Diagram — HORN — 15, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, when you read wiring diagrams, refer following.
When you perform trouble diagnosis, refer following, "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES", "How to Perform Efficient Diagnosis an Electrical Incident", check for any Service bulletins before servicing vehicle.
The front wiper switch is controlled by a lever built into combination switch, there are two front wiper switch positions, with the ignition switch in the ON or START position, power supplied, to front wiper motor terminal B.
Low and High Speed Wiper Operation, ground is supplied to front wiper switch terminal 17 through body grounds E12 E54, with the front wiper switch in the LO position, ground supplied, to front wiper motor terminal L.
Through front wiper switch terminal 14, with power and ground supplied, the front wiper motor operates low speed, with the front wiper switch in the HI position, ground supplied, to front wiper motor terminal H.
Through front wiper switch terminal 16, with power and ground supplied, the front wiper motor operates high speed, when the front wiper switch is turned OFF, the front wiper motor will continue to operate low speed until, when wiper blades are not located at base of windshield with front wiper switch OFF, ground supplied.
Through front wiper switch terminal 13, through front wiper motor terminal P, through front wiper motor terminal E, through body grounds E12 E54.
There are three front wiper switch positions, to front wiper switch terminal 19, when wiper blades reach base of windshield, front wiper motor terminals B and P connected instead, to front wiper switch terminal 13.
With battery voltage supplied to front wiper switch terminal 13, the front wiper switch will stop front wiper, motor with the wiper blades PARK position, the wiper blades perform a single wiping operation, followed by a delay interval which adjustable, approximately to 13 seconds, after which the cycle repeats.
When the front wiper switch is placed in the INT position, ground supplied intermittently, through front wiper switch terminal 17, the delay interval time is controlled by wiper switch, the wiper motor operates at low speed at desired delay interval.
To front washer motor terminal +, when the lever is pulled to the WASH position, ground supplied, to front washer motor terminal –.
Nissan Models