2003 Nissan Xterra - Seat Belt System (Section SB) (10 pages)
Download Seat Belt System (Section SB)
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 2, precautions for Seat Belt Service 2, tOP TETHER STRAP CHILD RESTRAINT 9, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted.
Information necessary to service the system safely is included in the SRS and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed.
Before removing the seat belt pre-tensioner assembly, turn the ignition switch OFF, disconnect, both battery cables and wait least 3 minutes, after replacing or reinstalling seat belt pre-tensioner assembly, or reconnecting seat belt pre-tensioner assembly connector, ensure entire SRS operates properly, do not disassemble buckle seat belt assembly.
Do not reuse seat belt anchor bolts after removal, replace anchor bolts if they are deformed worn out, if any component of seat belt assembly is questionable, do not repair, if webbing is cut, frayed, or damaged, replace seat belt assembly.
When replacing seat belt assembly, use a genuine NISSAN seat belt assembly, inspect all seat belt assemblies including retractors and attaching hardware after any collision, nISSAN recommends that all seat belt assemblies in use during a collision be replaced unless, collision was minor and the belts show no damage and continue to operate properly.
So could result in serious personal injury in an accident, collision should also be replaced if either damage or improper operation is noted, replace any seat belt assembly (including anchor bolts) if, the seat belt was in use at the time of a collision (except for minor collisions and belts, retractors.
Buckles show no damage and continue operate properly), the seat belt was damaged in an accident, the seat belt attaching point was damaged in an accident, or distortion and repair as necessary before installing a new seat belt assembly.
Anchor bolts are deformed worn out, the seat belt pre-tensioner should be replaced even if the seat belts are not in use during collision, which the air bags deployed, remove components in the order shown illustration above.
Slide the seat all the way forward and tilt the seatback toward front, when disconnecting or connecting direct-connect SRS connectors, refer SRS-7, "Direct-connect, remove retractor anchor bolt screw, installation is in the reverse order removal.
The rear seat must be removed to access the rear seat belt components, collision should also be replaced if either damage or improper operation noted, assemblies which are equipped with pre-tensioners should be replaced even if seat belts, the seat belt was in use at the time of a collision (except after minor collisions when belts, retractors.
And buckles show no damage and continue operate properly), the seat belt was damaged in an accident (i, the seat belt assembly is equipped with a pre-tensioner, even if the seat belt is not in use during a collision in which the air bags deployed, check the SEAT BELT” warning lamp for proper operation follows.
Also, the SEAT BELT” warning chime should sound about seven seconds, if the AIR BAG” warning lamp is blinking, conduct self-diagnosis using AIR BAG” warning lamp or CONSULT-II, check that the seat belt retractor, seat belt anchor and buckle bolts securely attached, check the shoulder seat belt guide and shoulder belt height adjuster for front seats.
Freely and that belt lays flat and does not bind in guide, fully extend the seat belt webbing and check for twists, tears other damage, allow the seat belt to retract.
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 2, precautions for Seat Belt Service 2, tOP TETHER STRAP CHILD RESTRAINT 9, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted.
Information necessary to service the system safely is included in the SRS and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed.
Before removing the seat belt pre-tensioner assembly, turn the ignition switch OFF, disconnect, both battery cables and wait least 3 minutes, after replacing or reinstalling seat belt pre-tensioner assembly, or reconnecting seat belt pre-tensioner assembly connector, ensure entire SRS operates properly, do not disassemble buckle seat belt assembly.
Do not reuse seat belt anchor bolts after removal, replace anchor bolts if they are deformed worn out, if any component of seat belt assembly is questionable, do not repair, if webbing is cut, frayed, or damaged, replace seat belt assembly.
When replacing seat belt assembly, use a genuine NISSAN seat belt assembly, inspect all seat belt assemblies including retractors and attaching hardware after any collision, nISSAN recommends that all seat belt assemblies in use during a collision be replaced unless, collision was minor and the belts show no damage and continue to operate properly.
So could result in serious personal injury in an accident, collision should also be replaced if either damage or improper operation is noted, replace any seat belt assembly (including anchor bolts) if, the seat belt was in use at the time of a collision (except for minor collisions and belts, retractors.
Buckles show no damage and continue operate properly), the seat belt was damaged in an accident, the seat belt attaching point was damaged in an accident, or distortion and repair as necessary before installing a new seat belt assembly.
Anchor bolts are deformed worn out, the seat belt pre-tensioner should be replaced even if the seat belts are not in use during collision, which the air bags deployed, remove components in the order shown illustration above.
Slide the seat all the way forward and tilt the seatback toward front, when disconnecting or connecting direct-connect SRS connectors, refer SRS-7, "Direct-connect, remove retractor anchor bolt screw, installation is in the reverse order removal.
The rear seat must be removed to access the rear seat belt components, collision should also be replaced if either damage or improper operation noted, assemblies which are equipped with pre-tensioners should be replaced even if seat belts, the seat belt was in use at the time of a collision (except after minor collisions when belts, retractors.
And buckles show no damage and continue operate properly), the seat belt was damaged in an accident (i, the seat belt assembly is equipped with a pre-tensioner, even if the seat belt is not in use during a collision in which the air bags deployed, check the SEAT BELT” warning lamp for proper operation follows.
Also, the SEAT BELT” warning chime should sound about seven seconds, if the AIR BAG” warning lamp is blinking, conduct self-diagnosis using AIR BAG” warning lamp or CONSULT-II, check that the seat belt retractor, seat belt anchor and buckle bolts securely attached, check the shoulder seat belt guide and shoulder belt height adjuster for front seats.
Freely and that belt lays flat and does not bind in guide, fully extend the seat belt webbing and check for twists, tears other damage, allow the seat belt to retract.
Nissan Models