2004 Nissan X-Trail - Exterior & Interior (Section EI) (40 pages)
Download Exterior & Interior (Section EI)
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 3, sQUEAK AND RATTLE TROUBLE DIAGNOSES 5, dUPLICATE THE NOISE AND TEST DRIVE 6, lOCATE THE NOISE AND IDENTIFY THE.
Generic Squeak Rattle Troubleshooting 7, removal and Installation (for Hyper Roof Rail) 27, removal and Installation (for Roof Rail) 28, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system.
Do not use electrical test equipment on any circuit related to the SRS unless instructed, when removing or disassembling any part, be careful not to damage or deform it, when removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl tape, keep removed parts protected with cloth.
If a clip is deformed damaged, replace it, if an unreusable part is removed, replace it with new one, tighten bolts and nuts firmly specified torque, after re-assembly has been completed, make sure each part functions correctly.
Dip a soft cloth in warm water, and then squeeze it tightly, dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off stain K, then wipe the area with soft dry cloth, sQUEAK AND RATTLE TROUBLE DIAGNOSES.
Interview the customer if possible, to determine the conditions that exist when the noise occurs, nostic Worksheet during the interview to document the facts and conditions when the noise occurs any, customer's comments; refer to EI-9, "Diagnostic Worksheet", conditions that exist when noise occurs.
Obtain all the facts and conditions that exist when the noise occurs (or does not occur), if there is more than one noise in the vehicle, be sure to diagnose and repair the noise that customer, after identifying the type of noise, isolate the noise in terms of its characteristics, are provided so the customer, service adviser and technician are all speaking same language when.
Squeak —(Like tennis shoes clean floor), squeak characteristics include the light contact/fast movement/brought on by road conditions/hard surL, faces=higher pitch noise/softer surfaces=lower pitch noises/edge surface=chirping, creak—(Like walking on an old wooden floor).
Creak characteristics include firm contact/slow movement/twisting with rotational movement/pitch, dependent on materials/often brought by activity, rattle characteristics include the fast repeated contact/vibration similar movement/loose parts/missing, knock —(Like a knock door).
Knock characteristics include hollow sounding/sometimes repeating/often brought by driver action, tick characteristics include gentle contacting of light materials/loose components/can be caused by driver, thump characteristics include softer knock/dead sound often drought by activity, buzz characteristics include high frequency rattle/firm contact.
Often the degree of acceptable noise level will vary depending upon the person, judge as acceptable may be very irritating customer, weather conditions, especially humidity and temperature, may have a great effect noise level, dUPLICATE THE NOISE AND TEST DRIVE.
If possible, drive the vehicle with the customer until the noise is duplicated, the Diagnostic Worksheet regarding the conditions or location of the noise, duplicate the same conditions when you confirm repair, tap or push/pull around the area where the noise appears be coming from.
Use a floor jack recreate vehicle twist”, at idle, apply engine load (electrical load, half-clutch on M/T model, drive position A/T model), raise the vehicle on a hoist and hit a tire with rubber hammer.
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 3, sQUEAK AND RATTLE TROUBLE DIAGNOSES 5, dUPLICATE THE NOISE AND TEST DRIVE 6, lOCATE THE NOISE AND IDENTIFY THE.
Generic Squeak Rattle Troubleshooting 7, removal and Installation (for Hyper Roof Rail) 27, removal and Installation (for Roof Rail) 28, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system.
Do not use electrical test equipment on any circuit related to the SRS unless instructed, when removing or disassembling any part, be careful not to damage or deform it, when removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl tape, keep removed parts protected with cloth.
If a clip is deformed damaged, replace it, if an unreusable part is removed, replace it with new one, tighten bolts and nuts firmly specified torque, after re-assembly has been completed, make sure each part functions correctly.
Dip a soft cloth in warm water, and then squeeze it tightly, dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off stain K, then wipe the area with soft dry cloth, sQUEAK AND RATTLE TROUBLE DIAGNOSES.
Interview the customer if possible, to determine the conditions that exist when the noise occurs, nostic Worksheet during the interview to document the facts and conditions when the noise occurs any, customer's comments; refer to EI-9, "Diagnostic Worksheet", conditions that exist when noise occurs.
Obtain all the facts and conditions that exist when the noise occurs (or does not occur), if there is more than one noise in the vehicle, be sure to diagnose and repair the noise that customer, after identifying the type of noise, isolate the noise in terms of its characteristics, are provided so the customer, service adviser and technician are all speaking same language when.
Squeak —(Like tennis shoes clean floor), squeak characteristics include the light contact/fast movement/brought on by road conditions/hard surL, faces=higher pitch noise/softer surfaces=lower pitch noises/edge surface=chirping, creak—(Like walking on an old wooden floor).
Creak characteristics include firm contact/slow movement/twisting with rotational movement/pitch, dependent on materials/often brought by activity, rattle characteristics include the fast repeated contact/vibration similar movement/loose parts/missing, knock —(Like a knock door).
Knock characteristics include hollow sounding/sometimes repeating/often brought by driver action, tick characteristics include gentle contacting of light materials/loose components/can be caused by driver, thump characteristics include softer knock/dead sound often drought by activity, buzz characteristics include high frequency rattle/firm contact.
Often the degree of acceptable noise level will vary depending upon the person, judge as acceptable may be very irritating customer, weather conditions, especially humidity and temperature, may have a great effect noise level, dUPLICATE THE NOISE AND TEST DRIVE.
If possible, drive the vehicle with the customer until the noise is duplicated, the Diagnostic Worksheet regarding the conditions or location of the noise, duplicate the same conditions when you confirm repair, tap or push/pull around the area where the noise appears be coming from.
Use a floor jack recreate vehicle twist”, at idle, apply engine load (electrical load, half-clutch on M/T model, drive position A/T model), raise the vehicle on a hoist and hit a tire with rubber hammer.
Nissan Models