2001 Nissan X-Trail - Transfer (Section TF) (60 pages)
Download Transfer (Section TF)
Manual Description
OIL LEAKAGE AND OIL LEVEL 8, how to proceed with trouble diagnosis 40, trouble diagnosis chart by symptom 41, control unit input/output signal standard 42.
CONTROL UNIT CONNECTOR TERMINAL ARRANGEMENT 42, cONTROL UNIT POWER SUPPLY SYSTEM 49, sOLENOID, ACTUATOR RELAY SYSTEM 52, iNDICATOR LAMP DOSE NOT COME ON.
FOR APPROXIMATELY SECOND WHEN THE, iGNITION SWITCH IS TURNED TO ON 55, wARNING LAMP DOES NOT ILLUMINATE, wARNING LAMP DOES NOT GO OUT.
OCCURS WHEN THE VEHICLE IS DRIVEN IN, aUTO MODE AND THE STEERING WHEEL IS, tURNED FULLY TO EITHER SIDE AFTER THE, mODES CANNOT BE SWITCHED AFTER.
VEHICLE DOES NOT ENTER 4WD MODE, eVEN THOUGH WARNING LAMP IS OFF58, wHEN THE VEHICLE IS STARTED IN AUTO, do not reuse drained transfer oil.
Check the oil level with the vehicle level ground, during removal and installation, be careful not to allow foreign material such as dust or dirt enter into, before starting diagnosis of the vehicle, understand trouble symptoms well, check for the correct installation status prior to removal or disassembly.
Certain they do not interfere with the function of the parts they applied to, carry out the work in a clean work place, before disassembly, using steam or white gasoline, completely remove sand and mud exterior, the unit, preventing them from entering into the unit during disassembly assembly.
Check appearance of the disassembled parts for damage, deformation, and abnormal wear, normally replace O-rings, oil seals, bearings, and lock nuts with new ones every time they removed, in principle, tighten bolts or nuts gradually in several steps working diagonally from inside outside, tightening sequence specified, observe it.
Clean and flush the parts sufficiently blow them dry, be careful not to damage sliding surfaces mating surfaces, always use shop paper for cleaning inside components, do not use cotton gloves or a shop cloth.
During assembly always tighten bolts and screws to specified torque, such as "Vaseline", or multi-purpose grease appropriate, discard waste oil after oil changes or part treatment in accordance with local laws regulations, side oil seal installation (adapter case oil.
Installing gear ring bearing inner race, installing gear ring bearing outer race, installing gear bearing inner race, removing gear ring bearing outer race.
Removing gear ring bearing inner race, installing pinion rear bearing outer race, installing pinion front bearing outer race, installing pinion front bearing inner race.
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING, refer to MA section("Checking Transfer Fluid", use the chart below to help you find the cause of the problem, run the vehicle to warm up transfer body sufficiently.
Stop the engine, and remove the drain plug drain transfer, apply recommended sealant to drain plug, on transfer and tighten specified torque.
Manual Description
OIL LEAKAGE AND OIL LEVEL 8, how to proceed with trouble diagnosis 40, trouble diagnosis chart by symptom 41, control unit input/output signal standard 42.
CONTROL UNIT CONNECTOR TERMINAL ARRANGEMENT 42, cONTROL UNIT POWER SUPPLY SYSTEM 49, sOLENOID, ACTUATOR RELAY SYSTEM 52, iNDICATOR LAMP DOSE NOT COME ON.
FOR APPROXIMATELY SECOND WHEN THE, iGNITION SWITCH IS TURNED TO ON 55, wARNING LAMP DOES NOT ILLUMINATE, wARNING LAMP DOES NOT GO OUT.
OCCURS WHEN THE VEHICLE IS DRIVEN IN, aUTO MODE AND THE STEERING WHEEL IS, tURNED FULLY TO EITHER SIDE AFTER THE, mODES CANNOT BE SWITCHED AFTER.
VEHICLE DOES NOT ENTER 4WD MODE, eVEN THOUGH WARNING LAMP IS OFF58, wHEN THE VEHICLE IS STARTED IN AUTO, do not reuse drained transfer oil.
Check the oil level with the vehicle level ground, during removal and installation, be careful not to allow foreign material such as dust or dirt enter into, before starting diagnosis of the vehicle, understand trouble symptoms well, check for the correct installation status prior to removal or disassembly.
Certain they do not interfere with the function of the parts they applied to, carry out the work in a clean work place, before disassembly, using steam or white gasoline, completely remove sand and mud exterior, the unit, preventing them from entering into the unit during disassembly assembly.
Check appearance of the disassembled parts for damage, deformation, and abnormal wear, normally replace O-rings, oil seals, bearings, and lock nuts with new ones every time they removed, in principle, tighten bolts or nuts gradually in several steps working diagonally from inside outside, tightening sequence specified, observe it.
Clean and flush the parts sufficiently blow them dry, be careful not to damage sliding surfaces mating surfaces, always use shop paper for cleaning inside components, do not use cotton gloves or a shop cloth.
During assembly always tighten bolts and screws to specified torque, such as "Vaseline", or multi-purpose grease appropriate, discard waste oil after oil changes or part treatment in accordance with local laws regulations, side oil seal installation (adapter case oil.
Installing gear ring bearing inner race, installing gear ring bearing outer race, installing gear bearing inner race, removing gear ring bearing outer race.
Removing gear ring bearing inner race, installing pinion rear bearing outer race, installing pinion front bearing outer race, installing pinion front bearing inner race.
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING, refer to MA section("Checking Transfer Fluid", use the chart below to help you find the cause of the problem, run the vehicle to warm up transfer body sufficiently.
Stop the engine, and remove the drain plug drain transfer, apply recommended sealant to drain plug, on transfer and tighten specified torque.
Nissan Models