2007 Nissan Versa - Engine Mechanical (Section EM) (116 pages)
Download Engine Mechanical (Section EM)
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 3, precautions for Procedures without Cowl Top Cover 3, precautions Necessary Steering Wheel Rotation, precautions for Disconnecting Fuel Piping 4.
Precautions for Removal Disassembly 4, precautions for Inspection, Repair Replacement 4, precautions for Assembly Installation 4, rEMOVAL OF LIQUID GASKET SEALING 5.
Use the Chart Below to Help You Find Cause, removal and Installation of Drive Belt Auto-Tensioner 14, aIR CLEANER AND AIR DUCT 16, iGNITION COIL, SPARK PLUG AND ROCKER.
FUEL INJECTOR AND FUEL TUBE 33, removal and Installation of Valve Oil Seal 59, removal and Installation of Front Oil Seal 60, removal and Installation of Rear Oil Seal 61.
How to Select Piston Bearing87, hOW TO SELECT CONNECTING ROD BEARING88, pISTON TO PISTON PIN OIL CLEARANCE95, oUT-OF-ROUND AND TAPER OF CRANKSHAFT 100.
CONNECTING ROD BEARING OIL CLEARANCE 101, mAIN BEARING CAP BOLT OUTER DIAMETER, cLOGGED OR DAMAGED OIL FILTER (FOR, sERVICE DATA AND SPECIFICATIONS (SDS) 105.
PISTON, PISTON RING AND PISTON PIN 111, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along EM, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front C, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, precautions for Procedures without Cowl Top Cover, when performing the procedure after removing cowl top cover, cover.
Precautions Necessary for Steering Wheel Rotation After Battery Disconnect, this Procedure is applied only to models with Intelligent Key system NATS (NISSAN ANTI-THEFT, remove and install all control units after disconnecting both battery cables with the ignition knob, always use CONSULT-II to perform self-diagnosis as a part of each function inspection after finishing.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mechanism is adopted key cylinder, for this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock, steering wheel rotation will become impossible, if steering wheel rotation is required when battery power is interrupted, follow procedure below before.
Supply power using jumper cables battery discharged, when the repair work is completed, return the ignition switch to the ″LOCK″ position before connecting, perform a self-diagnosis check of all control units using CONSULT-II, drain coolant when engine cooled.
Before starting work, make sure no fire or spark producing items are work area, after disconnecting pipes, plug openings stop fuel leakage, use torque wrench to tighten bolts nuts specification, when tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with.
Ones in center, then ones on inside and outside diagonally in this order, replace with new gasket, packing, oil seal O-ring, thoroughly wash, clean, and air-blow each part.
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 3, precautions for Procedures without Cowl Top Cover 3, precautions Necessary Steering Wheel Rotation, precautions for Disconnecting Fuel Piping 4.
Precautions for Removal Disassembly 4, precautions for Inspection, Repair Replacement 4, precautions for Assembly Installation 4, rEMOVAL OF LIQUID GASKET SEALING 5.
Use the Chart Below to Help You Find Cause, removal and Installation of Drive Belt Auto-Tensioner 14, aIR CLEANER AND AIR DUCT 16, iGNITION COIL, SPARK PLUG AND ROCKER.
FUEL INJECTOR AND FUEL TUBE 33, removal and Installation of Valve Oil Seal 59, removal and Installation of Front Oil Seal 60, removal and Installation of Rear Oil Seal 61.
How to Select Piston Bearing87, hOW TO SELECT CONNECTING ROD BEARING88, pISTON TO PISTON PIN OIL CLEARANCE95, oUT-OF-ROUND AND TAPER OF CRANKSHAFT 100.
CONNECTING ROD BEARING OIL CLEARANCE 101, mAIN BEARING CAP BOLT OUTER DIAMETER, cLOGGED OR DAMAGED OIL FILTER (FOR, sERVICE DATA AND SPECIFICATIONS (SDS) 105.
PISTON, PISTON RING AND PISTON PIN 111, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along EM, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front C, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, precautions for Procedures without Cowl Top Cover, when performing the procedure after removing cowl top cover, cover.
Precautions Necessary for Steering Wheel Rotation After Battery Disconnect, this Procedure is applied only to models with Intelligent Key system NATS (NISSAN ANTI-THEFT, remove and install all control units after disconnecting both battery cables with the ignition knob, always use CONSULT-II to perform self-diagnosis as a part of each function inspection after finishing.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mechanism is adopted key cylinder, for this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock, steering wheel rotation will become impossible, if steering wheel rotation is required when battery power is interrupted, follow procedure below before.
Supply power using jumper cables battery discharged, when the repair work is completed, return the ignition switch to the ″LOCK″ position before connecting, perform a self-diagnosis check of all control units using CONSULT-II, drain coolant when engine cooled.
Before starting work, make sure no fire or spark producing items are work area, after disconnecting pipes, plug openings stop fuel leakage, use torque wrench to tighten bolts nuts specification, when tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with.
Ones in center, then ones on inside and outside diagonally in this order, replace with new gasket, packing, oil seal O-ring, thoroughly wash, clean, and air-blow each part.
Nissan Models