2005 Nissan Titan - Road Wheels & Tires (Section WT) (34 pages)
Download Road Wheels & Tires (Section WT)
Manual Description
LOW TIRE PRESSURE WARNING SYSTEM 7, control Unit Input/Output Signal Standard 12, how to Perform Trouble Diagnosis Quick, inspection Transmitter or Control Unit (BCM) 23.
Inspection Transmitter - 1 23, inspection Transmitter - 2 24, inspection Vehicle Speed Signal 25, inspection Warning Lamp Does Not Come On.
When Ignition Switch Is Turned On 26, inspection Warning Lamp Flashes When Ignition, inspection Hazard Warning Lamp Flashes When, ignition Switch Is Turned On 29.
Inspection TIRE PRESSURE” Information In, display Unit Does Not Exist 30, inspection ID Registration Cannot Be Completed 30, sERVICE DATA AND SPECIFICATIONS (SDS) 33.
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, nOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING, refer to ROAD WHEEL chart, use the chart below to help you find the cause of the symptom.
Check tires for wear improper inflation, check wheels for deformation, cracks other damage, deformed, remove wheel check wheel runout, remove tire from wheel and mount wheel tire balance.
Set dial indicator as shown in the illustration, check front wheel bearings looseness, remove inner and outer balance weights wheel, be careful not to scratch wheel during removal.
Using releasing agent, remove double-faced adhesive tape wheel, after removing double-faced adhesive tape, wipe clean traces of releasing agent wheel, if a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting, select and adjust a drive-in weight mode suitable wheels.
Set wheel on wheel balancer using the center hole as a guide, when inner and outer imbalance values are shown on the wheel balancer indicator, multiply outer imbalance value by 1, a value closest to the calculated value and install it to the designated outer position of, or desig- F, nated angle in relation road wheel.
Q Before installing the balance weight, be sure to clean the mating surface wheel, indicated imbalance value × 5/3 = balance weight be installed, weight (closer to calculated balance weight value), note that balance weight value must be closer calculated.
Install balance weight position shown, when installing balance weight to wheels, set it into grooved, area on the inner wall of the wheel as shown so that balance, weight center is aligned with the wheel balancer indication position (angle).
Q Always use Genuine NISSAN adhesion balance weights, q Balance weights are not reusable; always replace with, q Do not install more than three sheets balance weights, if calculated balance weight value exceeds 50 g (1.
Two balance weight sheets in line with each other shown, do not install one balance weight sheet top another, install drive-in balance weight on inner side of road wheel, do not install more than two balance weights.
Imbalance values are 5 g (0, q If either residual imbalance value exceeds 5 g (0, follow the maintenance schedule for tire rotation service intervals.
Manual Description
LOW TIRE PRESSURE WARNING SYSTEM 7, control Unit Input/Output Signal Standard 12, how to Perform Trouble Diagnosis Quick, inspection Transmitter or Control Unit (BCM) 23.
Inspection Transmitter - 1 23, inspection Transmitter - 2 24, inspection Vehicle Speed Signal 25, inspection Warning Lamp Does Not Come On.
When Ignition Switch Is Turned On 26, inspection Warning Lamp Flashes When Ignition, inspection Hazard Warning Lamp Flashes When, ignition Switch Is Turned On 29.
Inspection TIRE PRESSURE” Information In, display Unit Does Not Exist 30, inspection ID Registration Cannot Be Completed 30, sERVICE DATA AND SPECIFICATIONS (SDS) 33.
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, nOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING, refer to ROAD WHEEL chart, use the chart below to help you find the cause of the symptom.
Check tires for wear improper inflation, check wheels for deformation, cracks other damage, deformed, remove wheel check wheel runout, remove tire from wheel and mount wheel tire balance.
Set dial indicator as shown in the illustration, check front wheel bearings looseness, remove inner and outer balance weights wheel, be careful not to scratch wheel during removal.
Using releasing agent, remove double-faced adhesive tape wheel, after removing double-faced adhesive tape, wipe clean traces of releasing agent wheel, if a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting, select and adjust a drive-in weight mode suitable wheels.
Set wheel on wheel balancer using the center hole as a guide, when inner and outer imbalance values are shown on the wheel balancer indicator, multiply outer imbalance value by 1, a value closest to the calculated value and install it to the designated outer position of, or desig- F, nated angle in relation road wheel.
Q Before installing the balance weight, be sure to clean the mating surface wheel, indicated imbalance value × 5/3 = balance weight be installed, weight (closer to calculated balance weight value), note that balance weight value must be closer calculated.
Install balance weight position shown, when installing balance weight to wheels, set it into grooved, area on the inner wall of the wheel as shown so that balance, weight center is aligned with the wheel balancer indication position (angle).
Q Always use Genuine NISSAN adhesion balance weights, q Balance weights are not reusable; always replace with, q Do not install more than three sheets balance weights, if calculated balance weight value exceeds 50 g (1.
Two balance weight sheets in line with each other shown, do not install one balance weight sheet top another, install drive-in balance weight on inner side of road wheel, do not install more than two balance weights.
Imbalance values are 5 g (0, q If either residual imbalance value exceeds 5 g (0, follow the maintenance schedule for tire rotation service intervals.
Nissan Models