2014 Nissan Sentra - Rear Axle (Section RAX) (9 pages)
Download Rear Axle (Section RAX)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, exploded View - Drum brake 6, removal and Installation - Drum brake 6, exploded View - Disc brake 7.
Removal and Installation - Disc brake 7, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery and wait at least three minutes before performing any service.
When installing each rubber part, final tightening must be carried out under unladen condition* with, *: Fuel, radiator coolant and engine oil full, after installing removed suspension parts, check wheel alignment, nOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING.
"Exploded View - Disc brake", use chart below to find the cause of the symptom, check the mounting conditions (looseness, back lash) of each component component conditions (wear, check the following items, and replace part it necessary.
Move wheel hub assembly in the axial direction by hand, rotate wheel hub assembly and check there is no unusual noise or other irregular conditions, of irregular conditions, replace wheel hub assembly, removal and Installation - Drum brake.
Remove the wheel and tire using power tool, remove the rear wheel sensor bolt (1) and the rear wheel sensor (2), do not depress brake pedal while rear brake drum removed, remove the hub bolts wheel hub assembly.
Do not remove parking brake assembly, installation is in the reverse order removal, check that the wheel hub assembly operates smoothly, removal and Installation - Disc brake.
Remove the rear brake caliper assembly, do not depress brake pedal while rear brake assembly removed, align the matching marks that have been made during removal when reusing disc rotor, check the wheel hub assembly for wear, cracks, and damage.
Check wheel sensor harness for proper connection, sERVICE DATA AND SPECIFICATIONS (SDS), < SERVICE DATA AND SPECIFICATIONS (SDS)...
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, exploded View - Drum brake 6, removal and Installation - Drum brake 6, exploded View - Disc brake 7.
Removal and Installation - Disc brake 7, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery and wait at least three minutes before performing any service.
When installing each rubber part, final tightening must be carried out under unladen condition* with, *: Fuel, radiator coolant and engine oil full, after installing removed suspension parts, check wheel alignment, nOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING.
"Exploded View - Disc brake", use chart below to find the cause of the symptom, check the mounting conditions (looseness, back lash) of each component component conditions (wear, check the following items, and replace part it necessary.
Move wheel hub assembly in the axial direction by hand, rotate wheel hub assembly and check there is no unusual noise or other irregular conditions, of irregular conditions, replace wheel hub assembly, removal and Installation - Drum brake.
Remove the wheel and tire using power tool, remove the rear wheel sensor bolt (1) and the rear wheel sensor (2), do not depress brake pedal while rear brake drum removed, remove the hub bolts wheel hub assembly.
Do not remove parking brake assembly, installation is in the reverse order removal, check that the wheel hub assembly operates smoothly, removal and Installation - Disc brake.
Remove the rear brake caliper assembly, do not depress brake pedal while rear brake assembly removed, align the matching marks that have been made during removal when reusing disc rotor, check the wheel hub assembly for wear, cracks, and damage.
Check wheel sensor harness for proper connection, sERVICE DATA AND SPECIFICATIONS (SDS), < SERVICE DATA AND SPECIFICATIONS (SDS)...
Nissan Models