2013 Nissan Sentra - Instrument Panel (Section IP) (24 pages)
Download Instrument Panel (Section IP)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, removal and Installation - Cluster Lid C20, removal and Installation - Cluster Lid C Lower20, sQUEAK AND RATTLE TROUBLE DIAGNOSES 8.
Generic Squeak Rattle Troubleshooting 10, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery and wait at least 3 minutes before performing any service.
When removing or disassembling each component, be careful not to damage or deform it, may be subject to interference, be sure to protect it with shop cloth, when removing (disengaging) components with a screwdriver or similar tool, be sure wrap component, with a shop cloth or vinyl tape protect it.
Protect the removed parts with a shop cloth and prevent them being dropped, replace a deformed damaged clip, be sure to tighten bolts and nuts securely specified torque, after installation is complete, be sure to check that each part works properly.
Follow the steps below clean components, dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe dirty area, then rub with soft, dry cloth, dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) wipe dirty.
Then dip a cloth into fresh water, wring the water out of the cloth and wipe detergent off, - For genuine leather seats, use a genuine leather seat cleaner, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, replace any clips which are damaged during removal installation.
SQUEAK AND RATTLE TROUBLE DIAGNOSES, interview the customer if possible, to determine the conditions that exist when the noise occurs, customer's comments; refer to IP-12, "Diagnostic Worksheet", conditions that exist when noise occurs.
All the facts and conditions that exist when the noise occurs (or does not occur), if there is more than one noise in the vehicle, be sure to diagnose and repair the noise that customer, after identifying the type of noise, isolate the noise in terms of its characteristics, are provided so the customer, service adviser and technician are all speaking same language when.
Squeak —(Like tennis shoes clean floor), squeak characteristics include the light contact/fast movement/brought on by road conditions/hard surfaces, = higher pitch noise/softer surfaces = lower pitch noises/edge surface = chirping, creak—(Like walking on an old wooden floor).
Creak characteristics include firm contact/slow movement/twisting with a rotational movement/pitch dependent on materials/often brought by activity, rattle characteristics include the fast repeated contact/vibration similar movement/loose parts/missing, knock —(Like a knock door), knock characteristics include hollow sounding/sometimes repeating/often brought by driver action.
Tick characteristics include gentle contacting of light materials/loose components/can be caused by driver, thump characteristics include softer knock/dead sound often brought by activity, buzz characteristics include high frequency rattle/firm contact, often the degree of acceptable noise level will vary depending upon the person.
As acceptable may be very irritating customer, weather conditions, especially humidity and temperature, may have a great effect noise level, dUPLICATE THE NOISE AND TEST DRIVE.
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, removal and Installation - Cluster Lid C20, removal and Installation - Cluster Lid C Lower20, sQUEAK AND RATTLE TROUBLE DIAGNOSES 8.
Generic Squeak Rattle Troubleshooting 10, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery and wait at least 3 minutes before performing any service.
When removing or disassembling each component, be careful not to damage or deform it, may be subject to interference, be sure to protect it with shop cloth, when removing (disengaging) components with a screwdriver or similar tool, be sure wrap component, with a shop cloth or vinyl tape protect it.
Protect the removed parts with a shop cloth and prevent them being dropped, replace a deformed damaged clip, be sure to tighten bolts and nuts securely specified torque, after installation is complete, be sure to check that each part works properly.
Follow the steps below clean components, dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe dirty area, then rub with soft, dry cloth, dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) wipe dirty.
Then dip a cloth into fresh water, wring the water out of the cloth and wipe detergent off, - For genuine leather seats, use a genuine leather seat cleaner, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, replace any clips which are damaged during removal installation.
SQUEAK AND RATTLE TROUBLE DIAGNOSES, interview the customer if possible, to determine the conditions that exist when the noise occurs, customer's comments; refer to IP-12, "Diagnostic Worksheet", conditions that exist when noise occurs.
All the facts and conditions that exist when the noise occurs (or does not occur), if there is more than one noise in the vehicle, be sure to diagnose and repair the noise that customer, after identifying the type of noise, isolate the noise in terms of its characteristics, are provided so the customer, service adviser and technician are all speaking same language when.
Squeak —(Like tennis shoes clean floor), squeak characteristics include the light contact/fast movement/brought on by road conditions/hard surfaces, = higher pitch noise/softer surfaces = lower pitch noises/edge surface = chirping, creak—(Like walking on an old wooden floor).
Creak characteristics include firm contact/slow movement/twisting with a rotational movement/pitch dependent on materials/often brought by activity, rattle characteristics include the fast repeated contact/vibration similar movement/loose parts/missing, knock —(Like a knock door), knock characteristics include hollow sounding/sometimes repeating/often brought by driver action.
Tick characteristics include gentle contacting of light materials/loose components/can be caused by driver, thump characteristics include softer knock/dead sound often brought by activity, buzz characteristics include high frequency rattle/firm contact, often the degree of acceptable noise level will vary depending upon the person.
As acceptable may be very irritating customer, weather conditions, especially humidity and temperature, may have a great effect noise level, dUPLICATE THE NOISE AND TEST DRIVE.
Nissan Models