2008 Nissan Sentra - Seat Belt System (Section SB) (10 pages)
Download Seat Belt System (Section SB)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution for Seat Belt Service 2, removal and Installation - 60:40 Split Fold Down, removal and Installation - Fixed Back Seat 9.
TOP TETHER STRAP CHILD RESTRAINT 10, removal and Installation of Front Seat Belt 3, removal and Installation of Rear Seat Belt 5, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, before removing the front seat belt pre-tensioner assembly, turn the ignition switch off, disconnect, the both battery cables and wait least 3 minutes.
After replacing or reinstalling front seat belt pre-tensioner assembly, or reconnecting front seat belt, pre-tensioner connector, check the system function, do not disassemble buckle seat belt assembly, do not reuse seat belt anchor bolts after removal.
Replace anchor bolts if they are deformed worn out, if webbing is cut, frayed, or damaged, replace seat belt assembly, when replacing seat belt assembly, use a genuine NISSAN seat belt assembly, inspect all seat belt assemblies including retractors and attaching hardware after any collision.
NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless, collision was minor and the belts show no damage and continue to operate properly, could result in serious personal injury in an accident, should be replaced even if the seat belts are not in use during a frontal collision in which air bags.
Replace any seat belt assembly (including anchor bolts) if, the seat belt was in use at the time of a collision (except for minor collisions and belts, retractors, buckles show no damage and continue operate properly), the seat belt was damaged in an accident.
The seat belt attaching point was damaged in an accident, or distortion and repair as necessary before installing a new seat belt assembly, anchor bolts are deformed worn out, the seat belt pre-tensioner should be replaced even if the seat belts are not in use during collision.
Which the air bags deployed, removal and Installation Front Seat Belt, outer anchor RH (belt tension sensor), before servicing the SRS, turn the ignition switch off, disconnect both battery cables wait least.
Disconnect both the negative and positive battery cables, then wait least 3 minutes, remove the seat belt adjuster cover shoulder anchor bolt, remove the retractor anchor bolt, then remove seat belt retractor, installation is in the reverse order removal.
Remove the floor center console assembly, disconnect the seat belt buckle harness connector (1), remove the buckle anchor bolt (A), then remove seat belt, removal and Installation Rear Seat Belt.
Remove the rear seat cushion and fold the seatback to the down position, remove the kicking plate upper and lower finishers, for RH/LH lower anchor, remove lower anchor bolt, for center lower anchor, release center latch.
Release the tabs and remove seat belt escutcheon, remove the rear parcel shelf finisher, remove the seat belt retractor anchor bolt, then remove seat belt retractor.
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution for Seat Belt Service 2, removal and Installation - 60:40 Split Fold Down, removal and Installation - Fixed Back Seat 9.
TOP TETHER STRAP CHILD RESTRAINT 10, removal and Installation of Front Seat Belt 3, removal and Installation of Rear Seat Belt 5, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, before removing the front seat belt pre-tensioner assembly, turn the ignition switch off, disconnect, the both battery cables and wait least 3 minutes.
After replacing or reinstalling front seat belt pre-tensioner assembly, or reconnecting front seat belt, pre-tensioner connector, check the system function, do not disassemble buckle seat belt assembly, do not reuse seat belt anchor bolts after removal.
Replace anchor bolts if they are deformed worn out, if webbing is cut, frayed, or damaged, replace seat belt assembly, when replacing seat belt assembly, use a genuine NISSAN seat belt assembly, inspect all seat belt assemblies including retractors and attaching hardware after any collision.
NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless, collision was minor and the belts show no damage and continue to operate properly, could result in serious personal injury in an accident, should be replaced even if the seat belts are not in use during a frontal collision in which air bags.
Replace any seat belt assembly (including anchor bolts) if, the seat belt was in use at the time of a collision (except for minor collisions and belts, retractors, buckles show no damage and continue operate properly), the seat belt was damaged in an accident.
The seat belt attaching point was damaged in an accident, or distortion and repair as necessary before installing a new seat belt assembly, anchor bolts are deformed worn out, the seat belt pre-tensioner should be replaced even if the seat belts are not in use during collision.
Which the air bags deployed, removal and Installation Front Seat Belt, outer anchor RH (belt tension sensor), before servicing the SRS, turn the ignition switch off, disconnect both battery cables wait least.
Disconnect both the negative and positive battery cables, then wait least 3 minutes, remove the seat belt adjuster cover shoulder anchor bolt, remove the retractor anchor bolt, then remove seat belt retractor, installation is in the reverse order removal.
Remove the floor center console assembly, disconnect the seat belt buckle harness connector (1), remove the buckle anchor bolt (A), then remove seat belt, removal and Installation Rear Seat Belt.
Remove the rear seat cushion and fold the seatback to the down position, remove the kicking plate upper and lower finishers, for RH/LH lower anchor, remove lower anchor bolt, for center lower anchor, release center latch.
Release the tabs and remove seat belt escutcheon, remove the rear parcel shelf finisher, remove the seat belt retractor anchor bolt, then remove seat belt retractor.
Nissan Models