2009 Nissan Rogue - LAN System (Section LAN) (127 pages)
Download LAN System (Section LAN)
Manual Description
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, fOR MEXICO : Precautions Trouble Diagnosis, fOR MEXICO : Precautions Harness Repair22, symptom When Error Occurs in CAN Communication System 9.
HOW TO USE THIS MANUAL 20, wiring Diagram - CAN SYSTEM -28, mAIN LINE BETWEEN DLC AND BCM CIRCUIT 32, mAIN LINE BETWEEN BCM AND TCM CIRCUIT 33.
MAIN LINE BETWEEN DLC AND BCM CIRCUIT 60, mAIN LINE BETWEEN BCM AND TCM CIRCUIT 61, mAIN LINE BETWEEN DLC AND BCM CIRCUIT 47, mAIN LINE BETWEEN BCM AND TCM CIRCUIT 48.
MAIN LINE BETWEEN DLC AND BCM CIRCUIT73, mAIN LINE BETWEEN BCM AND TCM CIRCUIT74, mAIN LINE BETWEEN DLC AND BCM CIRCUIT 101, mAIN LINE BETWEEN BCM AND TCM CIRCUIT 102.
MAIN LINE BETWEEN DLC AND BCM CIRCUIT87, mAIN LINE BETWEEN BCM AND TCM CIRCUIT88, bCM BRANCH LINE CIRCUIT 107 LAN, mAIN LINE BETWEEN DLC AND BCM CIRCUIT 114.
MAIN LINE BETWEEN BCM AND TCM CIRCUIT 115, use a tester with open terminal voltage of 7, turn the ignition switch OFF and disconnect the battery cable from negative terminal when, solder the repaired area and wrap tape around soldered area.
A fray of twisted lines must be within 110 mm (4, bypass connection is never allowed repaired area, bypass connection may cause CAN communication error, spliced wire becomes separated and characteristics twisted.
Replace the applicable harness as an assembly if error is detected on the shield lines CAN communication line, large quantities of data at high speed by connecting control units with two communication lines (CAN-H, control units on the CAN network transmit signals using the CAN communication control circuit, receive only necessary signals from other control units operate various functions.
CAN communication lines adopt twisted-pair line style (two lines twisted) noise immunity, each control unit passes an electric current to the termination circuits when transmitting CAN communication, communication system transmits and receives CAN communication signals by potential difference, cAN communication line between splice control unit.
A point connecting a branch line with main line, refer to "CAN Communication Control Circuit", it controls CAN communication signal transmission and reception, error detection, etc, it converts digital signal into CAN communication signal, and CAN communication signal into digital.
It eliminates noise CAN communication signal, *: These are the only control units wired with both ends CAN communication system, diag on CAN” is a diagnosis using CAN communication instead of previous DDL1 DDL2 communication, lines, between control units diagnosis unit.
It is used for trouble diagnosis, it is used for trouble diagnosis control, or is indicated on SELF-DIAG RESULTS on CONSULT-III if CAN communication signal, not transmitted or received between units for 2 seconds more.
CAN communication line open (CAN-H, CAN-L, both), cAN communication line short (ground, between CAN communication lines, other harnesses), error of CAN communication control circuit of the unit connected CAN communication line, wHEN OR U1001” IS INDICATED EVEN THOUGH CAN COMMUNICATION SYSTEM IS.
Removal/installation of parts: Error may be detected when removing and installing CAN communication unit, and related parts while turning the ignition switch ON, fuse blown out (removed): CAN communication of unit may cease.
Manual Description
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, fOR MEXICO : Precautions Trouble Diagnosis, fOR MEXICO : Precautions Harness Repair22, symptom When Error Occurs in CAN Communication System 9.
HOW TO USE THIS MANUAL 20, wiring Diagram - CAN SYSTEM -28, mAIN LINE BETWEEN DLC AND BCM CIRCUIT 32, mAIN LINE BETWEEN BCM AND TCM CIRCUIT 33.
MAIN LINE BETWEEN DLC AND BCM CIRCUIT 60, mAIN LINE BETWEEN BCM AND TCM CIRCUIT 61, mAIN LINE BETWEEN DLC AND BCM CIRCUIT 47, mAIN LINE BETWEEN BCM AND TCM CIRCUIT 48.
MAIN LINE BETWEEN DLC AND BCM CIRCUIT73, mAIN LINE BETWEEN BCM AND TCM CIRCUIT74, mAIN LINE BETWEEN DLC AND BCM CIRCUIT 101, mAIN LINE BETWEEN BCM AND TCM CIRCUIT 102.
MAIN LINE BETWEEN DLC AND BCM CIRCUIT87, mAIN LINE BETWEEN BCM AND TCM CIRCUIT88, bCM BRANCH LINE CIRCUIT 107 LAN, mAIN LINE BETWEEN DLC AND BCM CIRCUIT 114.
MAIN LINE BETWEEN BCM AND TCM CIRCUIT 115, use a tester with open terminal voltage of 7, turn the ignition switch OFF and disconnect the battery cable from negative terminal when, solder the repaired area and wrap tape around soldered area.
A fray of twisted lines must be within 110 mm (4, bypass connection is never allowed repaired area, bypass connection may cause CAN communication error, spliced wire becomes separated and characteristics twisted.
Replace the applicable harness as an assembly if error is detected on the shield lines CAN communication line, large quantities of data at high speed by connecting control units with two communication lines (CAN-H, control units on the CAN network transmit signals using the CAN communication control circuit, receive only necessary signals from other control units operate various functions.
CAN communication lines adopt twisted-pair line style (two lines twisted) noise immunity, each control unit passes an electric current to the termination circuits when transmitting CAN communication, communication system transmits and receives CAN communication signals by potential difference, cAN communication line between splice control unit.
A point connecting a branch line with main line, refer to "CAN Communication Control Circuit", it controls CAN communication signal transmission and reception, error detection, etc, it converts digital signal into CAN communication signal, and CAN communication signal into digital.
It eliminates noise CAN communication signal, *: These are the only control units wired with both ends CAN communication system, diag on CAN” is a diagnosis using CAN communication instead of previous DDL1 DDL2 communication, lines, between control units diagnosis unit.
It is used for trouble diagnosis, it is used for trouble diagnosis control, or is indicated on SELF-DIAG RESULTS on CONSULT-III if CAN communication signal, not transmitted or received between units for 2 seconds more.
CAN communication line open (CAN-H, CAN-L, both), cAN communication line short (ground, between CAN communication lines, other harnesses), error of CAN communication control circuit of the unit connected CAN communication line, wHEN OR U1001” IS INDICATED EVEN THOUGH CAN COMMUNICATION SYSTEM IS.
Removal/installation of parts: Error may be detected when removing and installing CAN communication unit, and related parts while turning the ignition switch ON, fuse blown out (removed): CAN communication of unit may cease.
Nissan Models