2009 Nissan Quest - Fuel System (Section FL) (13 pages)
Download Fuel System (Section FL)
Manual Description
FUEL LEVEL SENSOR UNIT, FUEL FILTER, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
The actual shapes of the Kent-Moore tools may differ from those of the special tools illustrated here, removing and installing fuel tank lock ring, inspect fuel lines, filler cap and tank improper attachment, leaks, cracks, damage, loose connections, chafing deterioration.
Or replace faulty parts necessary, when replacing fuel line parts, be sure observe following, put a CAUTION: FLAMMABLE” sign work area, be sure to work in a well ventilated area and have CO2 fire extinguisher.
Do not smoke while working on the fuel system, before removing fuel line parts, carry out following procedures, - Put drained fuel in an explosion-proof container and put the lid on securely, - Release fuel pressure from the fuel lines.
- Disconnect battery ground cable, always replace O-rings and clamps with new ones, after connecting the fuel tube quick connectors, make sure, ensure that the connector and resin tube do not contact any.
After installing the tubes, run the engine check fuel, leaks at the connections using following steps, - a) Apply fuel pressure to the fuel lines by turning ignition, switch to ON (without starting the engine).
Leaks at fuel tube connections, - b) Start the engine and rev the engine, then check fuel, use only a Genuine NISSAN fuel filler cap replacement, an incorrect fuel filler cap is used, the MIL may come on.
For servicing Evaporative Emission System” parts, refer, for servicing On Board Refueling Vapor Recovery (ORVR)”, fUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY, fuel level sensor unit, fuel filter.
Read General Precautions” before working fuel system, remove the fuel level sensor, fuel filter, fuel pump assembly, make sure the fuel level sensor, fuel filter, and fuel pump is free from defects foreign materials, installation is in the reverse order removal.
Install the fuel level sensor, fuel filter, and fuel pump assembly with, the fuel feed hose facing the front vehicle, turn the lock ring until the lock ring is fully rotated into fuel tank, connect the quick connector follows.
- Check the connection for damage any foreign materials, - Align the connector with the tube, then insert connector straight, into the tube until click heard, - After the tube is connected, make sure the connection secure by.
Pulling on the tube and the connector to make sure they, visually confirm that the two retainer tabs connected, use the following procedure to check fuel leaks.
Manual Description
FUEL LEVEL SENSOR UNIT, FUEL FILTER, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
The actual shapes of the Kent-Moore tools may differ from those of the special tools illustrated here, removing and installing fuel tank lock ring, inspect fuel lines, filler cap and tank improper attachment, leaks, cracks, damage, loose connections, chafing deterioration.
Or replace faulty parts necessary, when replacing fuel line parts, be sure observe following, put a CAUTION: FLAMMABLE” sign work area, be sure to work in a well ventilated area and have CO2 fire extinguisher.
Do not smoke while working on the fuel system, before removing fuel line parts, carry out following procedures, - Put drained fuel in an explosion-proof container and put the lid on securely, - Release fuel pressure from the fuel lines.
- Disconnect battery ground cable, always replace O-rings and clamps with new ones, after connecting the fuel tube quick connectors, make sure, ensure that the connector and resin tube do not contact any.
After installing the tubes, run the engine check fuel, leaks at the connections using following steps, - a) Apply fuel pressure to the fuel lines by turning ignition, switch to ON (without starting the engine).
Leaks at fuel tube connections, - b) Start the engine and rev the engine, then check fuel, use only a Genuine NISSAN fuel filler cap replacement, an incorrect fuel filler cap is used, the MIL may come on.
For servicing Evaporative Emission System” parts, refer, for servicing On Board Refueling Vapor Recovery (ORVR)”, fUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY, fuel level sensor unit, fuel filter.
Read General Precautions” before working fuel system, remove the fuel level sensor, fuel filter, fuel pump assembly, make sure the fuel level sensor, fuel filter, and fuel pump is free from defects foreign materials, installation is in the reverse order removal.
Install the fuel level sensor, fuel filter, and fuel pump assembly with, the fuel feed hose facing the front vehicle, turn the lock ring until the lock ring is fully rotated into fuel tank, connect the quick connector follows.
- Check the connection for damage any foreign materials, - Align the connector with the tube, then insert connector straight, into the tube until click heard, - After the tube is connected, make sure the connection secure by.
Pulling on the tube and the connector to make sure they, visually confirm that the two retainer tabs connected, use the following procedure to check fuel leaks.
Nissan Models