2007 Nissan Quest - Fuel System (Section FL) (14 pages)
Download Fuel System (Section FL)
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 2, fUEL LEVEL SENSOR UNIT, FUEL FILTER AND, sERVICE DATA AND SPECIFICATIONS (SDS) 13, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted.
Information necessary to service the system safely is included in the SRS and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed.
The actual shapes of the Kent-Moore tools may differ from those of the special tools illustrated here, removing and installing fuel tank lock ring, inspect fuel lines, filler cap and tank improper attachment, leaks, cracks, damage, loose connections, chafing deterioration.
Or replace faulty parts necessary, when replacing fuel line parts, be sure observe following, put a CAUTION: FLAMMABLE” sign work area, be sure to work in a well ventilated area and have CO2 fire extinguisher.
Do not smoke while working on the fuel system, before removing fuel line parts, carry out following procedures, put drained fuel in an explosion-proof container and put the lid on securely, release fuel pressure from the fuel lines.
Always replace O-rings and clamps with new ones, do not kink or twist tubes when they being installed, after connecting the fuel tube quick connectors, make sure, ensure that the connector and resin tube do not contact.
After installing the tubes, run the engine check fuel, leaks at the connections using following steps, a) Apply fuel pressure to the fuel lines by turning the ignition switch to ON (without starting engine), for fuel leaks at fuel tube connections.
B) Start the engine and rev the engine, then check fuel, leaks at fuel tube connections, use only a Genuine NISSAN fuel filler cap replacement, if an incorrect fuel filler cap is used, the MIL may come on.
For servicing Evaporative Emission System” parts, refer, for servicing On Board Refueling Vapor Recovery, (ORVR)” parts, refer to EC-39, "ON BOARD REFUELING, fUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY.
Fuel level sensor unit, fuel filter, read General Precautions” before working fuel system, remove the lock ring using a socket drive handle Tool, remove the fuel level sensor, fuel filter, fuel pump assembly.
Make sure the fuel level sensor, fuel filter, and fuel pump is free from defects foreign materials, installation is in the reverse order removal, install the fuel level sensor, fuel filter, fuel pump assembly, with the fuel feed hose facing the front vehicle.
Turn the lock ring until the lock ring is fully rotated into fuel, connect the quick connector follows, check the connection for damage any foreign materials, align the connector with the tube, then insert connector.
Straight into the tube until click heard, after the tube is connected, make sure connection secure, by pulling on the tube and the connector to make sure they.
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 2, fUEL LEVEL SENSOR UNIT, FUEL FILTER AND, sERVICE DATA AND SPECIFICATIONS (SDS) 13, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted.
Information necessary to service the system safely is included in the SRS and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed.
The actual shapes of the Kent-Moore tools may differ from those of the special tools illustrated here, removing and installing fuel tank lock ring, inspect fuel lines, filler cap and tank improper attachment, leaks, cracks, damage, loose connections, chafing deterioration.
Or replace faulty parts necessary, when replacing fuel line parts, be sure observe following, put a CAUTION: FLAMMABLE” sign work area, be sure to work in a well ventilated area and have CO2 fire extinguisher.
Do not smoke while working on the fuel system, before removing fuel line parts, carry out following procedures, put drained fuel in an explosion-proof container and put the lid on securely, release fuel pressure from the fuel lines.
Always replace O-rings and clamps with new ones, do not kink or twist tubes when they being installed, after connecting the fuel tube quick connectors, make sure, ensure that the connector and resin tube do not contact.
After installing the tubes, run the engine check fuel, leaks at the connections using following steps, a) Apply fuel pressure to the fuel lines by turning the ignition switch to ON (without starting engine), for fuel leaks at fuel tube connections.
B) Start the engine and rev the engine, then check fuel, leaks at fuel tube connections, use only a Genuine NISSAN fuel filler cap replacement, if an incorrect fuel filler cap is used, the MIL may come on.
For servicing Evaporative Emission System” parts, refer, for servicing On Board Refueling Vapor Recovery, (ORVR)” parts, refer to EC-39, "ON BOARD REFUELING, fUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY.
Fuel level sensor unit, fuel filter, read General Precautions” before working fuel system, remove the lock ring using a socket drive handle Tool, remove the fuel level sensor, fuel filter, fuel pump assembly.
Make sure the fuel level sensor, fuel filter, and fuel pump is free from defects foreign materials, installation is in the reverse order removal, install the fuel level sensor, fuel filter, fuel pump assembly, with the fuel feed hose facing the front vehicle.
Turn the lock ring until the lock ring is fully rotated into fuel, connect the quick connector follows, check the connection for damage any foreign materials, align the connector with the tube, then insert connector.
Straight into the tube until click heard, after the tube is connected, make sure connection secure, by pulling on the tube and the connector to make sure they.
Nissan Models