2005 Nissan Quest - Brake Control System (Section BRC) (100 pages)
Download Brake Control System (Section BRC)
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 3, cHECK POINTS FOR USING CONSULT-II 3, wiring Diagrams Trouble Diagnosis 5, how to Perform Trouble Diagnoses Quick.
Component Parts and Harness Connector Location 14, wiring Diagram — TCS — 16, bRAKE FLUID LEVEL, FLUID LEAK, AND, aBS WARNING LAMP, SLIP INDICATOR LAMP.
AND TCS OFF INDICATOR LAMP INSPECTION 20, warning Lamp Indicator Timing 21, control Unit Input/Output Signal Standard 21, actuator Motor, Motor Relay, Circuit Inspection 33.
Stop Lamp Switch System Inspection 34, aBS/TCS Control Unit Power Ground Systems, pedal Vibration or ABS Operation Noise 39, aBS Warning Lamp Does Not Come On When Ignition Switch Is Turned On 40.
ABS Warning Lamp Stays On When Ignition Switch, vehicle Jerks During TCS Activation 41, aCTUATOR AND ELECTRIC UNIT (ASSEMBLY) 44, (SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 46.
CHECK POINTS FOR USING CONSULT-II 46, wiring Diagrams Trouble Diagnosis 48, component Parts and Harness Connector Location 58, wiring Diagram — VDC — 60.
AND VDC OFF INDICATOR LAMP INSPECTION 65, warning Lamp Indicator Timing 66, control Unit Input/Output Signal Standard 66, yaw Rate/Side/Decel G Sensor System Inspection80.
Solenoid and VDC Change-Over Valve System, actuator Motor, Motor Relay, Circuit Inspection83, aBS/TCS/VDC Control Unit Power Ground, brake Fluid Level Sensor System Inspection86.
Pedal Vibration ABS Operation Noise90, aBS Warning Lamp Does Not Come On When Ignition Switch Is Turned On91, adjustment of Steering Angle Sensor Neutral Position93, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along B, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front C, air bag, depending on the severity of a collision and whether the front occupants belted unbelted.
Information necessary to service the system safely is included in the SRS and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed.
Refer to "RECOMMENDED FLUIDS AND LUBRICANTS" recommended brake fluid, be careful not to splash brake fluid on painted areas; it may cause paint damage, splashed on painted areas, wash it away with water immediately, to clean or wash all parts of master cylinder and disc brake caliper, use clean brake fluid.
Never use mineral oils such as gasoline or kerosene, use flare nut wrench when removing installing brake, if a brake fluid leak is found, the part must be disassembled, turn the ignition switch OFF and remove connector.
The ABS actuator and electric unit (control unit) or the battery terminal before performing work, always tighten brake lines to specified torque when installing, burnish the brake contact surfaces after refinishing.
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 3, cHECK POINTS FOR USING CONSULT-II 3, wiring Diagrams Trouble Diagnosis 5, how to Perform Trouble Diagnoses Quick.
Component Parts and Harness Connector Location 14, wiring Diagram — TCS — 16, bRAKE FLUID LEVEL, FLUID LEAK, AND, aBS WARNING LAMP, SLIP INDICATOR LAMP.
AND TCS OFF INDICATOR LAMP INSPECTION 20, warning Lamp Indicator Timing 21, control Unit Input/Output Signal Standard 21, actuator Motor, Motor Relay, Circuit Inspection 33.
Stop Lamp Switch System Inspection 34, aBS/TCS Control Unit Power Ground Systems, pedal Vibration or ABS Operation Noise 39, aBS Warning Lamp Does Not Come On When Ignition Switch Is Turned On 40.
ABS Warning Lamp Stays On When Ignition Switch, vehicle Jerks During TCS Activation 41, aCTUATOR AND ELECTRIC UNIT (ASSEMBLY) 44, (SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 46.
CHECK POINTS FOR USING CONSULT-II 46, wiring Diagrams Trouble Diagnosis 48, component Parts and Harness Connector Location 58, wiring Diagram — VDC — 60.
AND VDC OFF INDICATOR LAMP INSPECTION 65, warning Lamp Indicator Timing 66, control Unit Input/Output Signal Standard 66, yaw Rate/Side/Decel G Sensor System Inspection80.
Solenoid and VDC Change-Over Valve System, actuator Motor, Motor Relay, Circuit Inspection83, aBS/TCS/VDC Control Unit Power Ground, brake Fluid Level Sensor System Inspection86.
Pedal Vibration ABS Operation Noise90, aBS Warning Lamp Does Not Come On When Ignition Switch Is Turned On91, adjustment of Steering Angle Sensor Neutral Position93, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along B, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front C, air bag, depending on the severity of a collision and whether the front occupants belted unbelted.
Information necessary to service the system safely is included in the SRS and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed.
Refer to "RECOMMENDED FLUIDS AND LUBRICANTS" recommended brake fluid, be careful not to splash brake fluid on painted areas; it may cause paint damage, splashed on painted areas, wash it away with water immediately, to clean or wash all parts of master cylinder and disc brake caliper, use clean brake fluid.
Never use mineral oils such as gasoline or kerosene, use flare nut wrench when removing installing brake, if a brake fluid leak is found, the part must be disassembled, turn the ignition switch OFF and remove connector.
The ABS actuator and electric unit (control unit) or the battery terminal before performing work, always tighten brake lines to specified torque when installing, burnish the brake contact surfaces after refinishing.
Nissan Models