2014 Nissan Pathfinder - Brake Control System (Section BRC) (126 pages)

Model: 2014 Nissan Pathfinder
File size: 3.52 MB
Pages: 126 pages



Download Brake Control System (Section BRC)

Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 4, precaution for Brake Control System 5, hill start assist FUNCTION : System Diagram30, hill start assist FUNCTION : System Description30.

AND ELECTRIC UNIT (CONTROL UNIT)] 32, aBS Actuator and Electric Unit (Control Unit) 8, wheel Sensor Sensor Rotor 9, vDC FUNCTION : System Diagram 22.

VDC FUNCTION : System Description 22, aDJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION 55, cALIBRATION OF DECEL G SENSOR 57, bRAKE FLUID LEVEL SWITCH 88.

DECEL G SEN SET 90, pOWER AND GROUND SYSTEM 65, aBS SENSOR [ABNORMAL SIGNAL] 69, bRAKE PEDAL VIBRATION OR OPERATION SOUND OCCURS 115.

Exploded View - Front Wheel Sensor 118, removal and Installation - Front Wheel Sensor 118, exploded View - Rear Wheel Sensor 119, removal and Installation - Rear Wheel Sensor 120.

THE BRAKING DISTANCE IS LONG 113, aBS FUNCTION DOES NOT OPERATE 114, removal and Installation - Front Sensor Rotor 122, removal and Installation - Rear Sensor Rotor 122.

Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.

The event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.

When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery and wait at least three minutes before performing any service, clean any dust from the front brake and rear brake using a vacuum dust collector.

Brake fluid use refer to MA-15, "FOR USA AND CANADA : Fluids and Lubricants" (United States and Canada) or MA-16, "FOR MEXICO : Fluids Lubricants" (Mexico), do not reuse drained brake fluid, immediately and wash with water if it gets painted surface, always confirm the specified tightening torque when installing brake pipes.

After pressing the brake pedal more deeply or harder than normal driving, such as air bleeding, check each, always loosen the brake tube flare nut with flare nut wrench, tighten the brake tube flare nut to the specified torque with a crowfoot (A) torque wrench (B), always connect the battery terminal when moving vehicle.

Turn the ignition switch OFF and disconnect ABS actuator, electric unit (control unit) harness connector battery negative, check that no brake fluid leakage is present after replacing, just after starting vehicle after ignition switch is ON, brake pedal may vibrate or motor operating noise may.

When an error is indicated by ABS or another warning lamp, collect all necessary information customer B, (what symptoms are present under what conditions) and check for simple causes before starting diagnostic, if tire size and type are used in an improper combination or brake pads are not Genuine NISSAN parts, stop- C, ping distance or steering stability may deteriorate.

If aftermarket parts (car stereo, CD player, etc, pinches, open circuits, improper wiring, - When replacing the following parts with parts other than genuine parts or making modifications: Suspension- E.