2012 Nissan Pathfinder - Power Supply, Ground & Circuit Elements (Section PG) (77 pages)
Download Power Supply, Ground & Circuit Elements (Section PG)
Manual Description
POWER SUPPLY, GROUND & CIRCUIT ELEMENTS, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution Necessary for Steering Wheel Rotation After Battery Disconnect 2, precaution for Power Generation Variable Voltage.
FUSE AND FUSIBLE LINK BOX 73, iPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) 75, aDDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL 8, bATTERY NEGATIVE TERMINAL : Special Repair Requirement 8.
Wiring Diagram — Ignition Power Supply — 21, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, precaution Necessary for Steering Wheel Rotation After Battery Disconnect.
This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYSTEM), remove and install all control units after disconnecting both battery cables with the ignition knob, always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing work, dTC is detected, perform trouble diagnosis according self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mechanism is adopted key cylinder, for this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock, steering wheel rotation will become impossible, if steering wheel rotation is required when battery power is interrupted, follow procedure below before.
Supply power using jumper cables battery discharged, precaution for Power Generation Variable Voltage Control System, for this model, the battery current sensor that is installed to the negative battery cable measures, charging/discharging current of the battery and performs various engine controls.
The engine control system and battery discharge may occur, or ground wire directly battery terminal, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, multitasking battery electrical diagnostic station.
Tests batteries, starting and charging systems charges batteries, for operating instructions, refer diagnostic, if it becomes necessary to start the engine with a booster battery and jumper cables, use 12-volt, after connecting battery cables, ensure that they are tightly clamped to battery terminals good.
Never add distilled water through the hole used check specific gravity, the following precautions must be taken to prevent over-discharging battery, the battery surface (particularly its top) should always be kept, the terminal connections should be clean tight.
At every routine maintenance, check electrolyte level, this also applies to batteries designated low maintenance”, when the vehicle is not going to be used over long period, time, disconnect the battery cable from negative terminal.
The vehicle has an extended storage switch, turn it off, bATTERY DIAGNOSIS WITH EXP-800 NI OR GR8-1200 NI, to diagnose and confirm the condition of the battery, use the following special service tools.
Manual Description
POWER SUPPLY, GROUND & CIRCUIT ELEMENTS, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution Necessary for Steering Wheel Rotation After Battery Disconnect 2, precaution for Power Generation Variable Voltage.
FUSE AND FUSIBLE LINK BOX 73, iPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) 75, aDDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL 8, bATTERY NEGATIVE TERMINAL : Special Repair Requirement 8.
Wiring Diagram — Ignition Power Supply — 21, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, precaution Necessary for Steering Wheel Rotation After Battery Disconnect.
This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYSTEM), remove and install all control units after disconnecting both battery cables with the ignition knob, always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing work, dTC is detected, perform trouble diagnosis according self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mechanism is adopted key cylinder, for this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock, steering wheel rotation will become impossible, if steering wheel rotation is required when battery power is interrupted, follow procedure below before.
Supply power using jumper cables battery discharged, precaution for Power Generation Variable Voltage Control System, for this model, the battery current sensor that is installed to the negative battery cable measures, charging/discharging current of the battery and performs various engine controls.
The engine control system and battery discharge may occur, or ground wire directly battery terminal, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, multitasking battery electrical diagnostic station.
Tests batteries, starting and charging systems charges batteries, for operating instructions, refer diagnostic, if it becomes necessary to start the engine with a booster battery and jumper cables, use 12-volt, after connecting battery cables, ensure that they are tightly clamped to battery terminals good.
Never add distilled water through the hole used check specific gravity, the following precautions must be taken to prevent over-discharging battery, the battery surface (particularly its top) should always be kept, the terminal connections should be clean tight.
At every routine maintenance, check electrolyte level, this also applies to batteries designated low maintenance”, when the vehicle is not going to be used over long period, time, disconnect the battery cable from negative terminal.
The vehicle has an extended storage switch, turn it off, bATTERY DIAGNOSIS WITH EXP-800 NI OR GR8-1200 NI, to diagnose and confirm the condition of the battery, use the following special service tools.
Nissan Models