2013 Nissan Murano - Front Axle (Section FAX) (53 pages)
Download Front Axle (Section FAX)
Manual Description
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, fOR MEXICO : Precautions Drive Shaft 5, tRANSAXLE SIDE : Removal Installation16, rIGHT SIDE : Removal Installation19.
WHEEL SIDE : Disassembly Assembly21, tRANSAXLE SIDE : Disassembly Assembly22, lEFT SIDE : Removal Installation18, wHEEL SIDE : Removal Installation13.
FRONT WHEEL HUB AND KNUCKLE 8, fOR MEXICO : Precautions Drive Shaft 31, wHEEL SIDE : Removal Installation 39, tRANSAXLE SIDE : Removal Installation 42.
LEFT SIDE : Removal Installation 44, rIGHT SIDE : Removal Installation 45, wHEEL SIDE : Disassembly Assembly 47, tRANSAXLE SIDE : Disassembly Assembly 48.
FRONT WHEEL HUB AND KNUCKLE 34, fRONT WHEEL HUB AND KNUCKLE 36, nOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING, refer to DRIVE SHAFT chart.
Refer to FRONT AXLE chart, use chart below to find the cause of the symptom, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”, always observe the following items preventing accidental activation.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision that would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with, ignition ON or engine running, never use air or electric power tools or strike near sensor(s) with.
When using air or electric power tools or hammers, always switch the ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, observe the following precautions when disassembling assembling drive shaft, never disassemble joint sub-assembly because it non-overhaul parts.
Perform work in a location which is dust-free possible, clean the parts, before disassembling assembling, prevent the entry of foreign objects during disassembly service location, reassemble disassembled parts carefully in the correct order.
Clean disassembled parts (except for rubber parts) with kerosene which shall be removed by blowing with, air or wiping with paper waste, fOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG", fOR MEXICO : Precautions Drive Shaft.
The actual shapes of Kent-More tools may differ from those of special service tools illustrated here, fRONT WHEEL HUB AND KNUCKLE, make sure that the mounting conditions (looseness, backlash) of each component component conditions, move wheel hub and bearing assembly in the axial direction by hand.
Rotate wheel hub and bearing assembly and make sure there is no unusual noise or other irregular conditions, check drive shaft mounting point and joint for looseness other damage, check boot for cracks other damage.
Manual Description
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, fOR MEXICO : Precautions Drive Shaft 5, tRANSAXLE SIDE : Removal Installation16, rIGHT SIDE : Removal Installation19.
WHEEL SIDE : Disassembly Assembly21, tRANSAXLE SIDE : Disassembly Assembly22, lEFT SIDE : Removal Installation18, wHEEL SIDE : Removal Installation13.
FRONT WHEEL HUB AND KNUCKLE 8, fOR MEXICO : Precautions Drive Shaft 31, wHEEL SIDE : Removal Installation 39, tRANSAXLE SIDE : Removal Installation 42.
LEFT SIDE : Removal Installation 44, rIGHT SIDE : Removal Installation 45, wHEEL SIDE : Disassembly Assembly 47, tRANSAXLE SIDE : Disassembly Assembly 48.
FRONT WHEEL HUB AND KNUCKLE 34, fRONT WHEEL HUB AND KNUCKLE 36, nOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING, refer to DRIVE SHAFT chart.
Refer to FRONT AXLE chart, use chart below to find the cause of the symptom, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”, always observe the following items preventing accidental activation.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision that would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with, ignition ON or engine running, never use air or electric power tools or strike near sensor(s) with.
When using air or electric power tools or hammers, always switch the ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, observe the following precautions when disassembling assembling drive shaft, never disassemble joint sub-assembly because it non-overhaul parts.
Perform work in a location which is dust-free possible, clean the parts, before disassembling assembling, prevent the entry of foreign objects during disassembly service location, reassemble disassembled parts carefully in the correct order.
Clean disassembled parts (except for rubber parts) with kerosene which shall be removed by blowing with, air or wiping with paper waste, fOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG", fOR MEXICO : Precautions Drive Shaft.
The actual shapes of Kent-More tools may differ from those of special service tools illustrated here, fRONT WHEEL HUB AND KNUCKLE, make sure that the mounting conditions (looseness, backlash) of each component component conditions, move wheel hub and bearing assembly in the axial direction by hand.
Rotate wheel hub and bearing assembly and make sure there is no unusual noise or other irregular conditions, check drive shaft mounting point and joint for looseness other damage, check boot for cracks other damage.
Nissan Models