2004 Nissan Murano - Brake Control System (Section BRC) (110 pages)
Download Brake Control System (Section BRC)
Manual Description
How to Perform Trouble Diagnosis Quick, wiring Diagram — ABS — 14, control Unit Input/Output Signal Standard 18, for Fast Accurate Diagnosis 27.
BASIC INSPECTION BRAKE FLUID LEVEL, bASIC INSPECTION POWER SYSTEM TERMINAL LOOSENESS AND BATTERY INSPECTION 28, bASIC INSPECTION ABS WARNING LAMP, inspection Wheel Sensor System 29.
Inspection ABS Actuator Electric Unit (Control, inspection Solenoid Valve System 33, inspection CAN Communication Lines 34, inspection Actuator Motor, Motor Relay, Circuit 34.
Unit) Power Supply Ground Circuit 35, inspection G Sensor System 37, symptom Excessive ABS Function Operation Frequency 38, symptom Unexpected Pedal Action 38.
Symptom Long Stopping Distance 39, symptom ABS Function Dose Not Operate 40, symptom Pedal Vibration ABS Operation, aCTUATOR AND ELECTRIC UNIT (ASSEMBLY) 44.
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 45, adjustment of Steering Angle Sensor Neutral Position 48, calibration of Decel G Sensor 49, wiring Diagram — VDC — 60.
Control Unit Input/Output Signal Standard 66, for Fast Accurate Diagnosis 80, bASIC INSPECTION POWER SYSTEM TERMINAL LOOSENESS AND BATTERY INSPECTION 81, vDC OFF INDICATOR LAMP, SLIP INDICATOR.
Inspection VDC/TCS/ABS Control Unit System86, inspection Steering Angle Sensor System89, inspection Yaw Rate/Side/Decel G sensor System, inspection Solenoid VDC Change-Over Valve.
Inspection Actuator Motor, Motor Relay, Circuit93, unit) Power Supply Ground Circuit94, inspection Stop Lamp Switch System95, inspection Brake Fluid Level Sensor System96.
Inspection When ST ANG SEN SIGNAL”, inspection When DECEL G SEN SET” Appears, inspection When ESTM VEH SPD SIG” Appears, inspection VDC OFF Indicator Lamp Does Not.
Symptom Excessive ABS Function Operation Frequency99, symptom The Braking Distance Is Long 100, symptom ABS Function Does Not Operate 101, symptom Vehicle Jerks During VDC/TCS/ABS.
Recommended fluid is brake fluid DOT 3”, do not reuse drained brake fluid, be careful not to splash brake fluid painted areas, to clean or wash all parts of master cylinder, disc brake caliper and wheel cylinder, use clean brake fluid.
Never use mineral oils such as gasoline or kerosene, use flare nut wrench when removing installing brake tube, always torque brake lines when installing, before working, turn ignition switch OFF and disconnect electrical connectors of ABS actuator and electric control unit battery terminals.
Burnish the brake contact surfaces after refinishing replacing, drums or rotors, after replacing pads or linings, or soft pedal, refer to "BRAKE BURNISHING PROCEDURE".
Manual Description
How to Perform Trouble Diagnosis Quick, wiring Diagram — ABS — 14, control Unit Input/Output Signal Standard 18, for Fast Accurate Diagnosis 27.
BASIC INSPECTION BRAKE FLUID LEVEL, bASIC INSPECTION POWER SYSTEM TERMINAL LOOSENESS AND BATTERY INSPECTION 28, bASIC INSPECTION ABS WARNING LAMP, inspection Wheel Sensor System 29.
Inspection ABS Actuator Electric Unit (Control, inspection Solenoid Valve System 33, inspection CAN Communication Lines 34, inspection Actuator Motor, Motor Relay, Circuit 34.
Unit) Power Supply Ground Circuit 35, inspection G Sensor System 37, symptom Excessive ABS Function Operation Frequency 38, symptom Unexpected Pedal Action 38.
Symptom Long Stopping Distance 39, symptom ABS Function Dose Not Operate 40, symptom Pedal Vibration ABS Operation, aCTUATOR AND ELECTRIC UNIT (ASSEMBLY) 44.
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 45, adjustment of Steering Angle Sensor Neutral Position 48, calibration of Decel G Sensor 49, wiring Diagram — VDC — 60.
Control Unit Input/Output Signal Standard 66, for Fast Accurate Diagnosis 80, bASIC INSPECTION POWER SYSTEM TERMINAL LOOSENESS AND BATTERY INSPECTION 81, vDC OFF INDICATOR LAMP, SLIP INDICATOR.
Inspection VDC/TCS/ABS Control Unit System86, inspection Steering Angle Sensor System89, inspection Yaw Rate/Side/Decel G sensor System, inspection Solenoid VDC Change-Over Valve.
Inspection Actuator Motor, Motor Relay, Circuit93, unit) Power Supply Ground Circuit94, inspection Stop Lamp Switch System95, inspection Brake Fluid Level Sensor System96.
Inspection When ST ANG SEN SIGNAL”, inspection When DECEL G SEN SET” Appears, inspection When ESTM VEH SPD SIG” Appears, inspection VDC OFF Indicator Lamp Does Not.
Symptom Excessive ABS Function Operation Frequency99, symptom The Braking Distance Is Long 100, symptom ABS Function Does Not Operate 101, symptom Vehicle Jerks During VDC/TCS/ABS.
Recommended fluid is brake fluid DOT 3”, do not reuse drained brake fluid, be careful not to splash brake fluid painted areas, to clean or wash all parts of master cylinder, disc brake caliper and wheel cylinder, use clean brake fluid.
Never use mineral oils such as gasoline or kerosene, use flare nut wrench when removing installing brake tube, always torque brake lines when installing, before working, turn ignition switch OFF and disconnect electrical connectors of ABS actuator and electric control unit battery terminals.
Burnish the brake contact surfaces after refinishing replacing, drums or rotors, after replacing pads or linings, or soft pedal, refer to "BRAKE BURNISHING PROCEDURE".
Nissan Models