2004 Nissan Maxima - Enging Cooling System (Section CO) (28 pages)
Download Enging Cooling System (Section CO)
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 2, rEMOVAL OF LIQUID GASKET SEALING 2, cHECKING COOLING SYSTEM FOR LEAKS 10, disassembly and Assembly Radiator Fan 18.
WATER OUTLET AND WATER PIPING 26, sERVICE DATA AND SPECIFICATIONS (SDS) 27, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, after removing the bolts and nuts, separate mating surface.
Using the Tool remove sealant, be careful not to damage mating surfaces, in areas where the Tool is difficult to use, use plastic hammer, plastic hammer to slide the Tool (2) by tapping side.
If for some unavoidable reason a tool such flat-bladed, screwdriver is used, be careful not to damage mating surfaces, using a scraper, remove the old sealant adhering mating, q Remove the sealant completely from the groove mating.
Surfaces, mounting bolts, bolt holes, thoroughly clean the mating surfaces remove all adhering, attach the sealant tube tube presser, q Use Genuine RTV Silicone Sealant or equivalent.
Apply the sealant without breaks to specified location with, if there is a groove for the sealant application, apply the sealant groove, as for the bolt holes, normally apply sealant inside, within five minutes of sealant application, install mating.
If the sealant protrudes, wipe it off immediately, do not retighten after installation, after minutes or more have passed installation, fill, the engine with the specified oil and coolant.
If there are specific instructions in manual, observe them, the actual shapes of Kent-Moore tools may from those of special service tools illustrated here, removing oil pan timing chain case, pressing the tube liquid gasket.
Adapting radiator cap tester radiator cap, installing radiator upper lower tanks, removing radiator upper lower tanks, o-ring for damage, deterioration improper fitting.
Never remove the radiator cap when the engine is hot, wrap a thick cloth around the cap, check if the reservoir tank coolant level is within MIN MAX, adjust coolant level if it is too much too little.
To check for leakage, apply pressure to cooling system using, never remove the radiator cap when the engine hot, burns could occur from high pressure coolant escaping, higher pressure than specified may cause radiator damage.
Thoroughly wipe out the radiator filler neck to remove any waxy residue foreign material, pull the negative-pressure valve to open it check that it, q Check that there is no dirt or damage on the valve seat.
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 2, rEMOVAL OF LIQUID GASKET SEALING 2, cHECKING COOLING SYSTEM FOR LEAKS 10, disassembly and Assembly Radiator Fan 18.
WATER OUTLET AND WATER PIPING 26, sERVICE DATA AND SPECIFICATIONS (SDS) 27, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, after removing the bolts and nuts, separate mating surface.
Using the Tool remove sealant, be careful not to damage mating surfaces, in areas where the Tool is difficult to use, use plastic hammer, plastic hammer to slide the Tool (2) by tapping side.
If for some unavoidable reason a tool such flat-bladed, screwdriver is used, be careful not to damage mating surfaces, using a scraper, remove the old sealant adhering mating, q Remove the sealant completely from the groove mating.
Surfaces, mounting bolts, bolt holes, thoroughly clean the mating surfaces remove all adhering, attach the sealant tube tube presser, q Use Genuine RTV Silicone Sealant or equivalent.
Apply the sealant without breaks to specified location with, if there is a groove for the sealant application, apply the sealant groove, as for the bolt holes, normally apply sealant inside, within five minutes of sealant application, install mating.
If the sealant protrudes, wipe it off immediately, do not retighten after installation, after minutes or more have passed installation, fill, the engine with the specified oil and coolant.
If there are specific instructions in manual, observe them, the actual shapes of Kent-Moore tools may from those of special service tools illustrated here, removing oil pan timing chain case, pressing the tube liquid gasket.
Adapting radiator cap tester radiator cap, installing radiator upper lower tanks, removing radiator upper lower tanks, o-ring for damage, deterioration improper fitting.
Never remove the radiator cap when the engine is hot, wrap a thick cloth around the cap, check if the reservoir tank coolant level is within MIN MAX, adjust coolant level if it is too much too little.
To check for leakage, apply pressure to cooling system using, never remove the radiator cap when the engine hot, burns could occur from high pressure coolant escaping, higher pressure than specified may cause radiator damage.
Thoroughly wipe out the radiator filler neck to remove any waxy residue foreign material, pull the negative-pressure valve to open it check that it, q Check that there is no dirt or damage on the valve seat.
Nissan Models