2000 Nissan Maxima - Fuel & Exhaust Systems (Section FE) (12 pages)
Download Fuel & Exhaust Systems (Section FE)
Manual Description
Fuel Pump, Fuel Level Sensor Unit Fuel, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, loosening or tightening front rear, before installing a new oxygen sensor (Use.
¼ When removing accelerator wire, make a mark to indicate lock nut's initial position, ¼ Check that throttle valve opens fully when accelerator pedal is fully depressed, returns to idle position when pedal released, ¼ Check accelerator control parts for improper contact with any adjacent parts.
¼ When connecting accelerator wire, be careful not to twist scratch wire, ¼ Make sure the ASCD wire is not pulling throttle drum, ¼ For ASCD wire adjustment, refer EL-215, AUTOMATIC, inHg)] until the throttle drum becomes free from rod.
Make sure that there is clearance between throttle, if NG, refer EC-113, Basic Inspection”, tighten accelerator adjusting nut until throttle drum starts, from that position, turn back adjusting nut 1.
Remove vacuum pump and vacuum hose throttle, reinstall the original vacuum hose throttle opener, when replacing fuel line parts, be sure observe following, ¼ Put a CAUTION: FLAMMABLE” sign workshop.
¼ Be sure to furnish workshop with CO2 fire extinguisher, ¼ Do not smoke while servicing fuel system, ¼ Before removing fuel line parts, carry out following procedures, a) Put drained fuel in an explosion-proof container and put lid securely.
B) Release fuel pressure from fuel line, ¼ Always replace O-ring and clamps with new ones, ¼ Do not tighten hose clamps excessively avoid damaging hoses, ¼ After installing tubes, run engine and check for fuel leaks connections.
¼ Use only a genuine NISSAN fuel filler cap as a replacement, ¼ For inspection, refer to EC-42, On Board Refueling Vapor Recovery (ORVR)”, release fuel pressure fuel line, refer to Fuel Pressure Release”.
¼ Keep clean the connecting portion of tube, disconnect filler hose, vent hose and evaporation hose fuel, remove fuel tank mounting band bolts while supporting fuel, to install, reverse the removal procedure.
¼ Align mating marks on tubes and connectors correct installation, ¼ Align push in tabs with retainer openings, ¼ Be sure that the connecting portion of tube, ¼ Insert tube into the center of the connector until you hear.
After connecting quick connector, make sure connection, firmly made using following method, ¼ Pull on the fuel tube and connector to make sure they firmly, ¼ Start the engine, increase engine speed verify that there.
Fuel Pump, Fuel Level Sensor Unit Fuel Filter, remove inspection hole cover located under rear seat, for removal of quick connectors, refer to step 5, fuel Pump, Fuel Level Sensor Unit Fuel Filter (Cont'd).
Pull out the fuel level sensor unit fuel pump, remove flange of fuel level sensor unit fuel pump, using a screwdriver, remove the snap fit portion order, pull out the fuel tank temperature sensor harness.
¼ Using a screwdriver, remove the snap fit portion order, ¼ Put mating marks on tubes and connectors correct installation, installation is in reverse order removal.
Manual Description
Fuel Pump, Fuel Level Sensor Unit Fuel, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, loosening or tightening front rear, before installing a new oxygen sensor (Use.
¼ When removing accelerator wire, make a mark to indicate lock nut's initial position, ¼ Check that throttle valve opens fully when accelerator pedal is fully depressed, returns to idle position when pedal released, ¼ Check accelerator control parts for improper contact with any adjacent parts.
¼ When connecting accelerator wire, be careful not to twist scratch wire, ¼ Make sure the ASCD wire is not pulling throttle drum, ¼ For ASCD wire adjustment, refer EL-215, AUTOMATIC, inHg)] until the throttle drum becomes free from rod.
Make sure that there is clearance between throttle, if NG, refer EC-113, Basic Inspection”, tighten accelerator adjusting nut until throttle drum starts, from that position, turn back adjusting nut 1.
Remove vacuum pump and vacuum hose throttle, reinstall the original vacuum hose throttle opener, when replacing fuel line parts, be sure observe following, ¼ Put a CAUTION: FLAMMABLE” sign workshop.
¼ Be sure to furnish workshop with CO2 fire extinguisher, ¼ Do not smoke while servicing fuel system, ¼ Before removing fuel line parts, carry out following procedures, a) Put drained fuel in an explosion-proof container and put lid securely.
B) Release fuel pressure from fuel line, ¼ Always replace O-ring and clamps with new ones, ¼ Do not tighten hose clamps excessively avoid damaging hoses, ¼ After installing tubes, run engine and check for fuel leaks connections.
¼ Use only a genuine NISSAN fuel filler cap as a replacement, ¼ For inspection, refer to EC-42, On Board Refueling Vapor Recovery (ORVR)”, release fuel pressure fuel line, refer to Fuel Pressure Release”.
¼ Keep clean the connecting portion of tube, disconnect filler hose, vent hose and evaporation hose fuel, remove fuel tank mounting band bolts while supporting fuel, to install, reverse the removal procedure.
¼ Align mating marks on tubes and connectors correct installation, ¼ Align push in tabs with retainer openings, ¼ Be sure that the connecting portion of tube, ¼ Insert tube into the center of the connector until you hear.
After connecting quick connector, make sure connection, firmly made using following method, ¼ Pull on the fuel tube and connector to make sure they firmly, ¼ Start the engine, increase engine speed verify that there.
Fuel Pump, Fuel Level Sensor Unit Fuel Filter, remove inspection hole cover located under rear seat, for removal of quick connectors, refer to step 5, fuel Pump, Fuel Level Sensor Unit Fuel Filter (Cont'd).
Pull out the fuel level sensor unit fuel pump, remove flange of fuel level sensor unit fuel pump, using a screwdriver, remove the snap fit portion order, pull out the fuel tank temperature sensor harness.
¼ Using a screwdriver, remove the snap fit portion order, ¼ Put mating marks on tubes and connectors correct installation, installation is in reverse order removal.
Nissan Models