2014 Nissan Juke - Ventilation System (Section VTL) (17 pages)
Download Ventilation System (Section VTL)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precautions for Removing Battery Terminal 2, precaution for Procedure without Cowl Top Cover 3, cENTER VENTILATOR GRILLE : Removal.
SIDE DEFROSTER NOZZLE : Removal Installation 9, sIDE VENTILATOR GRILLE : Removal Installation 9, sIDE DEFROSTER GRILLE : Removal Installation 10, fRONT DEFROSTER NOZZLE : Removal Installation10.
CENTER VENTILATOR DUCT : Removal Installation11, sIDE VENTILATOR DUCT : Removal Installation11, rEAR HEATER DUCT 1 : Removal Installation11, rEAR HEATER DUCT 2 : Removal Installation12.
REAR HEATER DUCT 3 : Removal Installation12, fOOT DUCT : Removal Installation13, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”.
Always observe the following items preventing accidental activation, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision that would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal.
Injury caused by unintentional activation of the system, never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with.
Ignition ON or engine running, never use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, precautions for Removing Battery Terminal.
When removing the 12V battery terminal, turn OFF ignition, switch and wait least 30 seconds, stops, then a DTC detection error or ECU data corruption may, for vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON ignition switch.
If the ignition switch is turned ON with any one terminals, main battery and sub battery disconnected, then DTC may be, after installing the 12V battery, always check "Self Diagnosis Result" of all ECUs erase DTC, the removal of 12V battery may cause DTC detection error.
Precaution for Procedure without Cowl Top Cover, when performing the procedure after removing cowl top cover, cover, the lower end of windshield with urethane, etc prevent damage, remove clips, pawls metal clips.
Ventilation system is controlled by A/C auto amp, (AUTOMATIC AIR CONDITIONING), HAC-104, "System Description" (MANUAL AIR CONDITIONING), : Indicates that the part is connected at points with same symbol actual vehicle, cENTER VENTILATOR GRILLE : Removal Installation.
Install in the reverse order removal, sIDE DEFROSTER NOZZLE : Removal Installation, remove fixing screws (A), and then remove side defroster nozzle, remove fixing screws (A), and then remove instrument panel.
Remove fixing screw (B), and then remove side defroster nozzle, sIDE VENTILATOR GRILLE : Removal Installation, sIDE DEFROSTER GRILLE : Removal Installation.
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precautions for Removing Battery Terminal 2, precaution for Procedure without Cowl Top Cover 3, cENTER VENTILATOR GRILLE : Removal.
SIDE DEFROSTER NOZZLE : Removal Installation 9, sIDE VENTILATOR GRILLE : Removal Installation 9, sIDE DEFROSTER GRILLE : Removal Installation 10, fRONT DEFROSTER NOZZLE : Removal Installation10.
CENTER VENTILATOR DUCT : Removal Installation11, sIDE VENTILATOR DUCT : Removal Installation11, rEAR HEATER DUCT 1 : Removal Installation11, rEAR HEATER DUCT 2 : Removal Installation12.
REAR HEATER DUCT 3 : Removal Installation12, fOOT DUCT : Removal Installation13, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”.
Always observe the following items preventing accidental activation, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision that would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal.
Injury caused by unintentional activation of the system, never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with.
Ignition ON or engine running, never use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, precautions for Removing Battery Terminal.
When removing the 12V battery terminal, turn OFF ignition, switch and wait least 30 seconds, stops, then a DTC detection error or ECU data corruption may, for vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON ignition switch.
If the ignition switch is turned ON with any one terminals, main battery and sub battery disconnected, then DTC may be, after installing the 12V battery, always check "Self Diagnosis Result" of all ECUs erase DTC, the removal of 12V battery may cause DTC detection error.
Precaution for Procedure without Cowl Top Cover, when performing the procedure after removing cowl top cover, cover, the lower end of windshield with urethane, etc prevent damage, remove clips, pawls metal clips.
Ventilation system is controlled by A/C auto amp, (AUTOMATIC AIR CONDITIONING), HAC-104, "System Description" (MANUAL AIR CONDITIONING), : Indicates that the part is connected at points with same symbol actual vehicle, cENTER VENTILATOR GRILLE : Removal Installation.
Install in the reverse order removal, sIDE DEFROSTER NOZZLE : Removal Installation, remove fixing screws (A), and then remove side defroster nozzle, remove fixing screws (A), and then remove instrument panel.
Remove fixing screw (B), and then remove side defroster nozzle, sIDE VENTILATOR GRILLE : Removal Installation, sIDE DEFROSTER GRILLE : Removal Installation.
Nissan Models