2014 Nissan Juke - Glasses, Window System & Mirrors (Section GW) (24 pages)
Download Glasses, Window System & Mirrors (Section GW)
Manual Description
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution for Procedure without Cowl Top Cover 2, precautions for Removing Battery Terminal 3.
Handling for Adhesive Primer 3, sQUEAK AND RATTLE TROUBLE DIAGNOSES 5, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”.
Always observe the following items preventing accidental activation, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision that would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal.
Injury caused by unintentional activation of the system, never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with.
Ignition ON or engine running, never use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, precaution for Procedure without Cowl Top Cover.
When performing the procedure after removing cowl top cover, cover, the lower end of windshield with urethane, etc prevent damage, precautions for Removing Battery Terminal, when removing the 12V battery terminal, turn OFF ignition.
Switch and wait least 30 seconds, stops, then a DTC detection error or ECU data corruption may, for vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON ignition switch, if the ignition switch is turned ON with any one terminals.
Main battery and sub battery disconnected, then DTC may be, after installing the 12V battery, always check "Self Diagnosis Result" of all ECUs erase DTC, the removal of 12V battery may cause DTC detection error, never use an adhesive that is past its usable date.
Keep primers and adhesive in a cool, dry place, open the seal of the primer and adhesive just before application, before application, be sure to shake the primer container to stir the contents, when using primer and adhesive, always observe the precautions instruction manual.
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, holds the windshield glass, front door glass, rear door glass and back door window glass, removes the clips, pawls metal clips.
SQUEAK AND RATTLE TROUBLE DIAGNOSES, interview the customer if possible, to determine the conditions that exist when the noise occurs, conditions that exist when noise occurs, all the facts and conditions that exist when the noise occurs (or does not occur).
If there is more than one noise in the vehicle, perform a diagnosis and repair the noise that customer J, after identifying the type of noise, isolate the noise in terms of its characteristics, are provided so that the customer, service adviser, and technician use the same language when describing, squeak – (Like tennis shoes clean floor).
Squeak characteristics include the light contact / fast movement / brought on by road conditions / hard surL, faces = high-pitched noise / softer surfaces = low-pitched noises / edge surface = chirping, creak – (Like walking on an old wooden floor).
Manual Description
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution for Procedure without Cowl Top Cover 2, precautions for Removing Battery Terminal 3.
Handling for Adhesive Primer 3, sQUEAK AND RATTLE TROUBLE DIAGNOSES 5, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”.
Always observe the following items preventing accidental activation, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision that would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal.
Injury caused by unintentional activation of the system, never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with.
Ignition ON or engine running, never use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, precaution for Procedure without Cowl Top Cover.
When performing the procedure after removing cowl top cover, cover, the lower end of windshield with urethane, etc prevent damage, precautions for Removing Battery Terminal, when removing the 12V battery terminal, turn OFF ignition.
Switch and wait least 30 seconds, stops, then a DTC detection error or ECU data corruption may, for vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON ignition switch, if the ignition switch is turned ON with any one terminals.
Main battery and sub battery disconnected, then DTC may be, after installing the 12V battery, always check "Self Diagnosis Result" of all ECUs erase DTC, the removal of 12V battery may cause DTC detection error, never use an adhesive that is past its usable date.
Keep primers and adhesive in a cool, dry place, open the seal of the primer and adhesive just before application, before application, be sure to shake the primer container to stir the contents, when using primer and adhesive, always observe the precautions instruction manual.
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, holds the windshield glass, front door glass, rear door glass and back door window glass, removes the clips, pawls metal clips.
SQUEAK AND RATTLE TROUBLE DIAGNOSES, interview the customer if possible, to determine the conditions that exist when the noise occurs, conditions that exist when noise occurs, all the facts and conditions that exist when the noise occurs (or does not occur).
If there is more than one noise in the vehicle, perform a diagnosis and repair the noise that customer J, after identifying the type of noise, isolate the noise in terms of its characteristics, are provided so that the customer, service adviser, and technician use the same language when describing, squeak – (Like tennis shoes clean floor).
Squeak characteristics include the light contact / fast movement / brought on by road conditions / hard surL, faces = high-pitched noise / softer surfaces = low-pitched noises / edge surface = chirping, creak – (Like walking on an old wooden floor).
Nissan Models