2014 Nissan Juke - Engine L System (Section Lu) (18 pages)
Download Engine L System (Section Lu)
Manual Description
Precautions for Removing Battery Terminal 2, precautions for Removing Battery Terminal, when removing the 12V battery terminal, turn OFF ignition, switch and wait least 30 seconds.
Stops, then a DTC detection error or ECU data corruption may, for vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON ignition switch, if the ignition switch is turned ON with any one terminals, main battery and sub battery disconnected, then DTC may be.
After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs erase DTC, the removal of 12V battery may cause DTC detection error, before starting work, check no fire or spark producing items are work area, release fuel pressure before disconnecting disassembly.
After disconnecting pipes, plug openings stop fuel leakage, drain engine coolant and engine oil when engine cooled, before repairing or replacing, thoroughly inspect parts, when instructed to use SST, use specified tools.
Exercise maximum care to avoid damage to mating sliding surfaces, dowel pins are used for several parts alignment, check that dowel pins are installed original position, must cover openings of engine system with a tape or equivalent, to seal out foreign materials.
Mark and arrange disassembly parts in an organized way for easy troubleshooting reassembly, when loosening nuts and bolts, as a basic rule, start with the one furthest outside, then one diagonally, use torque wrench to tighten bolts nuts specification, when tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with.
Ones in center, then ones on inside and outside diagonally in this order, replace with new gasket, packing, oil seal O-ring, thoroughly wash, clean, and air-blow each part, avoid damaging sliding or mating surfaces.
Before assembly, oil sliding surfaces well, after disassembling, or exposing any internal engine parts, change engine oil and replace oil filter with new, release air within route when refilling after draining engine coolant, after repairing, start the engine and increase engine speed to check engine coolant, fuel, engine oil.
After removing mounting nuts and bolts, separate the mating surface using the seal cutter [SST: KV10111100 (J-37228)] (A), be careful not to damage mating surfaces, tap the seal cutter [SST: KV10111100 (J-37228)] insert it (B), and then slide it (C) by tapping on the side as shown figure.
In areas where the seal cutter [SST: KV10111100 (J-37228)] is difficult to use, lightly tap the parts using a plastic hammer remove, if for some unavoidable reason tool such screwdriver, used, be careful not to damage mating surfaces, using a scraper (A), remove old liquid gasket adhering to the liquid gasket application surface mating surface.
Remove liquid gasket completely from the groove liquid, gasket application surface, mounting bolts, bolt holes, wipe the liquid gasket application surface and the mating surface with white gasoline (lighting and heating use) remove, adhering moisture, grease foreign materials.
Attach liquid gasket tube to the tube presser (commercial service tool), use Genuine RTV silicon sealant or equivalent, apply liquid gasket without gaps to the specified location according specified dimensions, as for bolt holes (B), normally apply liquid gasket inside.
Check to read the text manual, within five minutes of liquid gasket application, install mating component, if liquid gasket protrudes, wipe it off immediately, do not retighten mounting bolts or nuts after installation.
After minutes or more have passed from the installation, fill engine oil engine coolant, if there are specific instructions in manual, observe them, maximum measuring range: 2,452 kPa (25.
Manual Description
Precautions for Removing Battery Terminal 2, precautions for Removing Battery Terminal, when removing the 12V battery terminal, turn OFF ignition, switch and wait least 30 seconds.
Stops, then a DTC detection error or ECU data corruption may, for vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON ignition switch, if the ignition switch is turned ON with any one terminals, main battery and sub battery disconnected, then DTC may be.
After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs erase DTC, the removal of 12V battery may cause DTC detection error, before starting work, check no fire or spark producing items are work area, release fuel pressure before disconnecting disassembly.
After disconnecting pipes, plug openings stop fuel leakage, drain engine coolant and engine oil when engine cooled, before repairing or replacing, thoroughly inspect parts, when instructed to use SST, use specified tools.
Exercise maximum care to avoid damage to mating sliding surfaces, dowel pins are used for several parts alignment, check that dowel pins are installed original position, must cover openings of engine system with a tape or equivalent, to seal out foreign materials.
Mark and arrange disassembly parts in an organized way for easy troubleshooting reassembly, when loosening nuts and bolts, as a basic rule, start with the one furthest outside, then one diagonally, use torque wrench to tighten bolts nuts specification, when tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with.
Ones in center, then ones on inside and outside diagonally in this order, replace with new gasket, packing, oil seal O-ring, thoroughly wash, clean, and air-blow each part, avoid damaging sliding or mating surfaces.
Before assembly, oil sliding surfaces well, after disassembling, or exposing any internal engine parts, change engine oil and replace oil filter with new, release air within route when refilling after draining engine coolant, after repairing, start the engine and increase engine speed to check engine coolant, fuel, engine oil.
After removing mounting nuts and bolts, separate the mating surface using the seal cutter [SST: KV10111100 (J-37228)] (A), be careful not to damage mating surfaces, tap the seal cutter [SST: KV10111100 (J-37228)] insert it (B), and then slide it (C) by tapping on the side as shown figure.
In areas where the seal cutter [SST: KV10111100 (J-37228)] is difficult to use, lightly tap the parts using a plastic hammer remove, if for some unavoidable reason tool such screwdriver, used, be careful not to damage mating surfaces, using a scraper (A), remove old liquid gasket adhering to the liquid gasket application surface mating surface.
Remove liquid gasket completely from the groove liquid, gasket application surface, mounting bolts, bolt holes, wipe the liquid gasket application surface and the mating surface with white gasoline (lighting and heating use) remove, adhering moisture, grease foreign materials.
Attach liquid gasket tube to the tube presser (commercial service tool), use Genuine RTV silicon sealant or equivalent, apply liquid gasket without gaps to the specified location according specified dimensions, as for bolt holes (B), normally apply liquid gasket inside.
Check to read the text manual, within five minutes of liquid gasket application, install mating component, if liquid gasket protrudes, wipe it off immediately, do not retighten mounting bolts or nuts after installation.
After minutes or more have passed from the installation, fill engine oil engine coolant, if there are specific instructions in manual, observe them, maximum measuring range: 2,452 kPa (25.
Nissan Models