2013 Nissan Altima - Exhaust System (Section EX) (11 pages)
Download Exhaust System (Section EX)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 7, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal.
Injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect.
Battery and wait at least 3 minutes before performing any service, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, loosening or tightening heated oxygen sensors, before installing a new oxygen sensor (Use.
Or equivalent meeting MIL specification MIL-A-907), check the exhaust pipes, muffler, mounting components, incorrect attachment, leaks, cracks, damage, deterioration, perform the procedure with the exhaust system fully cooled down because the system will be hot.
Just after the engine turned off, use genuine NISSAN exhaust system parts or equivalent, which are specifically designed heat, remove exhaust system components using power tools, remove heated oxygen sensor using Tool needed.
Installation is in the reverse order removal, always replace exhaust gaskets with new ones when reassembling, before installing a new heated oxygen sensor, clean and lube the exhaust tube threads using suitable tool, discard any heated oxygen sensor which has been dropped from a height of more than 0.
In) onto a hard surface such as a concrete floor; install new one, resulting in MIL coming on, if any mounting insulator is badly deformed, repair or replace it, the mounting insulator, clean inspect them.
When installing the insulator avoid large gaps or interference between insulator each, remove deposits from the sealing surface of each connection, temporarily tighten the exhaust manifold side nuts and the vehicle side bolts, any interference, and then tighten the nuts bolts specification.
When installing each mounting rubber, avoid twisting or excessive extension up/down right, tighten the bolts without causing interference with flange, with the engine running, check the exhaust tube joints for exhaust gas leaks abnormal noise, check that the mounting brackets and mounting insulators are installed properly free excessive.
Oxygen sensor thread cleaner : (J-43897-18), oxygen sensor thread cleaner : (J-43897-12), with the engine running, check the exhaust tube joints for exhaust gas leaks unusual noises...
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 7, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal.
Injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect.
Battery and wait at least 3 minutes before performing any service, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, loosening or tightening heated oxygen sensors, before installing a new oxygen sensor (Use.
Or equivalent meeting MIL specification MIL-A-907), check the exhaust pipes, muffler, mounting components, incorrect attachment, leaks, cracks, damage, deterioration, perform the procedure with the exhaust system fully cooled down because the system will be hot.
Just after the engine turned off, use genuine NISSAN exhaust system parts or equivalent, which are specifically designed heat, remove exhaust system components using power tools, remove heated oxygen sensor using Tool needed.
Installation is in the reverse order removal, always replace exhaust gaskets with new ones when reassembling, before installing a new heated oxygen sensor, clean and lube the exhaust tube threads using suitable tool, discard any heated oxygen sensor which has been dropped from a height of more than 0.
In) onto a hard surface such as a concrete floor; install new one, resulting in MIL coming on, if any mounting insulator is badly deformed, repair or replace it, the mounting insulator, clean inspect them.
When installing the insulator avoid large gaps or interference between insulator each, remove deposits from the sealing surface of each connection, temporarily tighten the exhaust manifold side nuts and the vehicle side bolts, any interference, and then tighten the nuts bolts specification.
When installing each mounting rubber, avoid twisting or excessive extension up/down right, tighten the bolts without causing interference with flange, with the engine running, check the exhaust tube joints for exhaust gas leaks abnormal noise, check that the mounting brackets and mounting insulators are installed properly free excessive.
Oxygen sensor thread cleaner : (J-43897-18), oxygen sensor thread cleaner : (J-43897-12), with the engine running, check the exhaust tube joints for exhaust gas leaks unusual noises...
Nissan Models