2013 Nissan Altima - Audio Visual System (Section AV) (413 pages)
Download Audio Visual System (Section AV)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 8, pOWER SUPPLY AND GROUND CIRCUIT 29, pOWER SUPPLY AND GROUND CIRCUIT 85, aUDIO UNIT : Diagnosis Procedure 85.
REAR VIEW CAMERA IMAGE SIGNAL CIRCUIT 92, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 55, pOWER SUPPLY AND GROUND CIRCUIT 155, aUDIO UNIT : Diagnosis Procedure 155.
BOSE SPEAKER AMP : Diagnosis Procedure 155, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 118, rEAR VIEW CAMERA IMAGE SIGNAL CIRCUIT 172, cONTROL UNIT : Work Procedure 232.
CONFIGURATION (AV CONTROL UNIT) : Description 233, cONFIGURATION (AV CONTROL UNIT) : Work, cONFIGURATION (AV CONTROL UNIT) : Configuration List 234, (SRS) "AIR BAG" "SEAT BELT PRE-TENSIONER"203.
POWER SUPPLY AND GROUND CIRCUIT 255, rEAR VIEW CAMERA IMAGE SIGNAL CIRCUIT 262, aV CONTROL UNIT : Diagnosis Procedure 255, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 296.
CONFIGURATION (AV CONTROL UNIT) : Description334, cONFIGURATION (AV CONTROL UNIT) : Configuration List335, pOWER SUPPLY AND GROUND CIRCUIT 357, aV CONTROL UNIT : Diagnosis Procedure 357.
BOSE SPEAKER AMP : Diagnosis Procedure 357, rEAR VIEW CAMERA IMAGE SIGNAL CIRCUIT 374, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal.
Injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect.
Battery and wait at least 3 minutes before performing any service, do not apply voltage of 7, use the tester with its open terminal voltage being 7, be sure to turn ignition switch OFF and disconnect the battery cable from negative terminal before.
Solder the repaired parts, and wrap with tape, must be within 110 mm (4, do not perform bypass wire connections for repair parts, spliced wire will become separated characteristics.
When removing or disassembling each component, be careful not to damage or deform it, may be subject to interference, be sure to protect it with shop cloth, when removing (disengaging) components with a screwdriver or similar tool, be sure wrap component, with a shop cloth or vinyl tape protect it.
Protect the removed parts with a shop cloth and prevent them being dropped, replace a deformed damaged clip, be sure to tighten bolts and nuts securely specified torque, after installation is complete, be sure to check that each part works properly.
Follow the steps below clean components, dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe dirty area, then rub with soft, dry cloth.
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 8, pOWER SUPPLY AND GROUND CIRCUIT 29, pOWER SUPPLY AND GROUND CIRCUIT 85, aUDIO UNIT : Diagnosis Procedure 85.
REAR VIEW CAMERA IMAGE SIGNAL CIRCUIT 92, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 55, pOWER SUPPLY AND GROUND CIRCUIT 155, aUDIO UNIT : Diagnosis Procedure 155.
BOSE SPEAKER AMP : Diagnosis Procedure 155, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 118, rEAR VIEW CAMERA IMAGE SIGNAL CIRCUIT 172, cONTROL UNIT : Work Procedure 232.
CONFIGURATION (AV CONTROL UNIT) : Description 233, cONFIGURATION (AV CONTROL UNIT) : Work, cONFIGURATION (AV CONTROL UNIT) : Configuration List 234, (SRS) "AIR BAG" "SEAT BELT PRE-TENSIONER"203.
POWER SUPPLY AND GROUND CIRCUIT 255, rEAR VIEW CAMERA IMAGE SIGNAL CIRCUIT 262, aV CONTROL UNIT : Diagnosis Procedure 255, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 296.
CONFIGURATION (AV CONTROL UNIT) : Description334, cONFIGURATION (AV CONTROL UNIT) : Configuration List335, pOWER SUPPLY AND GROUND CIRCUIT 357, aV CONTROL UNIT : Diagnosis Procedure 357.
BOSE SPEAKER AMP : Diagnosis Procedure 357, rEAR VIEW CAMERA IMAGE SIGNAL CIRCUIT 374, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal.
Injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect.
Battery and wait at least 3 minutes before performing any service, do not apply voltage of 7, use the tester with its open terminal voltage being 7, be sure to turn ignition switch OFF and disconnect the battery cable from negative terminal before.
Solder the repaired parts, and wrap with tape, must be within 110 mm (4, do not perform bypass wire connections for repair parts, spliced wire will become separated characteristics.
When removing or disassembling each component, be careful not to damage or deform it, may be subject to interference, be sure to protect it with shop cloth, when removing (disengaging) components with a screwdriver or similar tool, be sure wrap component, with a shop cloth or vinyl tape protect it.
Protect the removed parts with a shop cloth and prevent them being dropped, replace a deformed damaged clip, be sure to tighten bolts and nuts securely specified torque, after installation is complete, be sure to check that each part works properly.
Follow the steps below clean components, dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe dirty area, then rub with soft, dry cloth.
Nissan Models