2010 Nissan Altima - Accelerator Control System (Section ACC) (5 pages)
Download Accelerator Control System (Section ACC)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, disconnect the accelerator position sensor electrical connector.
Remove the three accelerator pedal nuts, remove the accelerator pedal and accelerator position sensor assembly, for electrical inspection of the accelerator pedal position sensor, avoid impact dropping during handling.
Keep the pedal assembly away water, installation is in the reverse order removal, align and install accelerator pedal and accelerator position sensor assembly with locating pins locating pin, check the accelerator pedal for smooth operation.
Check that the accelerator pedal moves through full specified, when the harness connector of the accelerator pedal position sensor disconnected, perform, pOSITION LEARNING : Special Repair Requirement" (QR25DE for California), EC-574, "ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair Requirement" (QR25DE except for California), EC-1069, "ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair, sERVICE DATA AND SPECIFICATIONS (SDS).
< SERVICE DATA AND SPECIFICATIONS (SDS), accelerator pedal - total travel (A)...
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, disconnect the accelerator position sensor electrical connector.
Remove the three accelerator pedal nuts, remove the accelerator pedal and accelerator position sensor assembly, for electrical inspection of the accelerator pedal position sensor, avoid impact dropping during handling.
Keep the pedal assembly away water, installation is in the reverse order removal, align and install accelerator pedal and accelerator position sensor assembly with locating pins locating pin, check the accelerator pedal for smooth operation.
Check that the accelerator pedal moves through full specified, when the harness connector of the accelerator pedal position sensor disconnected, perform, pOSITION LEARNING : Special Repair Requirement" (QR25DE for California), EC-574, "ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair Requirement" (QR25DE except for California), EC-1069, "ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair, sERVICE DATA AND SPECIFICATIONS (SDS).
< SERVICE DATA AND SPECIFICATIONS (SDS), accelerator pedal - total travel (A)...
Nissan Models