2014 Nissan 370Z - Brake Control System (Section BRC) (116 pages)
Download Brake Control System (Section BRC)
Manual Description
CONTROL UNIT : Special Repair Requirement 8, nEUTRAL POSITION : Special Repair Requirement 8, aND ELECTRIC UNIT (CONTROL UNIT)] 22, pOWER AND GROUND SYSTEM 35.
ABS MOTOR, MOTOR RELAY SYSTEM 38, c1126 IN ABS SOL 50, c1127 OUT ABS SOL 52, yAW RATE/SIDE G SENSOR 63.
BRAKE FLUID LEVEL SWITCH 68, pOWER SUPPLY AND GROUND CIRCUIT 74, fOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, fOR MEXICO : Precaution Battery Service 105.
FOR MEXICO : Precaution Procedure without, fOR MEXICO : Precaution Brake System 106, fOR MEXICO : Precaution Brake Control 106, fOR MEXICO : Precautions Harness Repair 106.
Wiring Diagram - BRAKE CONTROL SYSTEM - 89, fRONT WHEEL SENSOR : Exploded View 109, fRONT WHEEL SENSOR : Removal Installation 109, rEAR WHEEL SENSOR : Exploded View 110.
REAR WHEEL SENSOR : Removal Installation 110, fRONT SENSOR ROTOR : Exploded View 111, fRONT SENSOR ROTOR : Removal Installation 111, rEAR SENSOR ROTOR : Exploded View 111.
REAR SENSOR ROTOR : Removal Installation 111, if steering angle sensor, steering system parts, suspension system parts, ABS actuator and electric unit (control unit) or tires have been replaced, or if wheel alignment has been adjusted, be sure to adjust neutral position of steering angle sensor before driving, get the detailed information from the customer about the symptom (the condition environment when, the incident/malfunction occurred) using the diagnosis work sheet.
YES >> Record or print self-diagnosis results and freeze frame data (FFD), perform the diagnosis applicable to the displayed DTC of ABS” with CONSULT, check that the symptom is a normal operation that is not considered a system malfunction, is the symptom normal operation.
Check that the warning lamp indicator lamp illuminate, aBS warning lamp: Refer BRC-80, "Description", brake warning lamp: Refer BRC-81, "Description", vDC OFF indicator lamp: Refer BRC-83, "Description".
VDC warning lamp: Refer BRC-82, "Description", perform the diagnosis applicable to the symptom ABS” with CONSULT, repair or replace specified malfunctioning parts, perform self-diagnosis memory clear ABS” with CONSULT.
Perform the self-diagnosis again, and check that the malfunction repaired completely, is no other DTC present repair completed, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description.
After replacing the ABS actuator and electric unit (control unit), perform the neutral position adjustment, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement, perform the neutral position adjustment for steering angle sensor, >> Refer to BRC-8, "ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement".
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION, aDJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Description, when doing work that applies to the list below, make sure to adjust neutral position steering angle sensor, adjustment of steering angle sensor neutral position.
Removing/Installing ABS actuator and electric unit (control unit), replacing ABS actuator and electric unit (control unit), aDJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement.
Manual Description
CONTROL UNIT : Special Repair Requirement 8, nEUTRAL POSITION : Special Repair Requirement 8, aND ELECTRIC UNIT (CONTROL UNIT)] 22, pOWER AND GROUND SYSTEM 35.
ABS MOTOR, MOTOR RELAY SYSTEM 38, c1126 IN ABS SOL 50, c1127 OUT ABS SOL 52, yAW RATE/SIDE G SENSOR 63.
BRAKE FLUID LEVEL SWITCH 68, pOWER SUPPLY AND GROUND CIRCUIT 74, fOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, fOR MEXICO : Precaution Battery Service 105.
FOR MEXICO : Precaution Procedure without, fOR MEXICO : Precaution Brake System 106, fOR MEXICO : Precaution Brake Control 106, fOR MEXICO : Precautions Harness Repair 106.
Wiring Diagram - BRAKE CONTROL SYSTEM - 89, fRONT WHEEL SENSOR : Exploded View 109, fRONT WHEEL SENSOR : Removal Installation 109, rEAR WHEEL SENSOR : Exploded View 110.
REAR WHEEL SENSOR : Removal Installation 110, fRONT SENSOR ROTOR : Exploded View 111, fRONT SENSOR ROTOR : Removal Installation 111, rEAR SENSOR ROTOR : Exploded View 111.
REAR SENSOR ROTOR : Removal Installation 111, if steering angle sensor, steering system parts, suspension system parts, ABS actuator and electric unit (control unit) or tires have been replaced, or if wheel alignment has been adjusted, be sure to adjust neutral position of steering angle sensor before driving, get the detailed information from the customer about the symptom (the condition environment when, the incident/malfunction occurred) using the diagnosis work sheet.
YES >> Record or print self-diagnosis results and freeze frame data (FFD), perform the diagnosis applicable to the displayed DTC of ABS” with CONSULT, check that the symptom is a normal operation that is not considered a system malfunction, is the symptom normal operation.
Check that the warning lamp indicator lamp illuminate, aBS warning lamp: Refer BRC-80, "Description", brake warning lamp: Refer BRC-81, "Description", vDC OFF indicator lamp: Refer BRC-83, "Description".
VDC warning lamp: Refer BRC-82, "Description", perform the diagnosis applicable to the symptom ABS” with CONSULT, repair or replace specified malfunctioning parts, perform self-diagnosis memory clear ABS” with CONSULT.
Perform the self-diagnosis again, and check that the malfunction repaired completely, is no other DTC present repair completed, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description.
After replacing the ABS actuator and electric unit (control unit), perform the neutral position adjustment, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement, perform the neutral position adjustment for steering angle sensor, >> Refer to BRC-8, "ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement".
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION, aDJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Description, when doing work that applies to the list below, make sure to adjust neutral position steering angle sensor, adjustment of steering angle sensor neutral position.
Removing/Installing ABS actuator and electric unit (control unit), replacing ABS actuator and electric unit (control unit), aDJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement.
Nissan Models