2004 Nissan 350Z - Engine Mechanical (Section EM) (154 pages)
Download Engine Mechanical (Section EM)
Manual Description
Precautions for Drain Engine Coolant 3, precautions for Disconnecting Fuel Piping 3, precautions for Removal Disassembly 3, precautions for Inspection, Repair Replacement 3.
Precautions for Assembly Installation 3, rEMOVAL OF LIQUID GASKET SEALING 4, use the Chart Below to Help You Find Cause, aIR CLEANER AND AIR DUCT 14.
EXHAUST MANIFOLD AND THREE WAY CATALYST 23, fUEL INJECTOR AND FUEL TUBE 36, fRONT TIMING CHAIN CASE 45, removal and Installation of Valve Oil Seal 87.
Removal and Installation of Front Oil Seal 88, removal and Installation of Rear Oil Seal 88, how to Select Piston Bearing 122, hOW TO SELECT CONNECTING ROD BEARING 123.
HOW TO SELECT MAIN BEARING 124, pISTON TO PISTON PIN OIL CLEARANCE 128, cONNECTING ROD BEND AND TORSION 130, cONNECTING ROD BIG END DIAMETER 130.
CONNECTING ROD BUSHING OIL CLEARANCE 130, cONNECTING ROD BEARING OIL CLEARANCE 134, cRUSH HEIGHT OF MAIN BEARING 136, mAIN BEARING CAP BOLT OUTER DIAMETER.
SERVICE DATA AND SPECIFICATIONS (SDS) 139, pISTON, PISTON RING AND PISTON PIN 147, before disconnecting the battery, lower both the driver and passenger windows, window slightly raises and lowers automatically to prevent any window to vehicle interference.
Window function will not work with battery disconnected, drain engine coolant when engine cooled, before starting work, make sure no fire or spark producing items are work area, release fuel pressure before disconnecting disassembly.
After disconnecting pipes, plug openings stop fuel leakage, when instructed to use SST, use specified tools, exercise maximum care to avoid damage to mating sliding surfaces, cover openings of engine system with tape or equivalent, if necessary, to seal out foreign materials.
Mark and arrange disassembly parts in an organized way for easy troubleshooting re-assembly, when loosening nuts and bolts, as a basic rule, start with the one furthest outside, then one diagonally, precautions for Inspection, Repair Replacement, before repairing or replacing, thoroughly inspect parts.
Use torque wrench to tighten bolts nuts specification, when tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with, ones in center, then ones on inside and outside diagonally in this order, replace with new gasket, packing, oil seal O-ring.
Dowel pins are used for several parts alignment, make sure that dowel pins are installed original position, thoroughly wash, clean, and air-blow each part, avoid damaging sliding or mating surfaces.
Before assembly, oil sliding surfaces well, release air within route when refilling after draining engine coolant, after repairing, start engine and increase engine speed to check engine coolant, fuel, engine oil, use angle wrench [SST: KV10112100 (BT8653-A)] for the final tightening of following engine parts.
Crankshaft pulley bolt (No angle wrench is required as bolt flange is provided with notches angle tightening), the torque value for these parts are preliminary step, ensure thread and seat surfaces are clean and coated with engine oil.
Manual Description
Precautions for Drain Engine Coolant 3, precautions for Disconnecting Fuel Piping 3, precautions for Removal Disassembly 3, precautions for Inspection, Repair Replacement 3.
Precautions for Assembly Installation 3, rEMOVAL OF LIQUID GASKET SEALING 4, use the Chart Below to Help You Find Cause, aIR CLEANER AND AIR DUCT 14.
EXHAUST MANIFOLD AND THREE WAY CATALYST 23, fUEL INJECTOR AND FUEL TUBE 36, fRONT TIMING CHAIN CASE 45, removal and Installation of Valve Oil Seal 87.
Removal and Installation of Front Oil Seal 88, removal and Installation of Rear Oil Seal 88, how to Select Piston Bearing 122, hOW TO SELECT CONNECTING ROD BEARING 123.
HOW TO SELECT MAIN BEARING 124, pISTON TO PISTON PIN OIL CLEARANCE 128, cONNECTING ROD BEND AND TORSION 130, cONNECTING ROD BIG END DIAMETER 130.
CONNECTING ROD BUSHING OIL CLEARANCE 130, cONNECTING ROD BEARING OIL CLEARANCE 134, cRUSH HEIGHT OF MAIN BEARING 136, mAIN BEARING CAP BOLT OUTER DIAMETER.
SERVICE DATA AND SPECIFICATIONS (SDS) 139, pISTON, PISTON RING AND PISTON PIN 147, before disconnecting the battery, lower both the driver and passenger windows, window slightly raises and lowers automatically to prevent any window to vehicle interference.
Window function will not work with battery disconnected, drain engine coolant when engine cooled, before starting work, make sure no fire or spark producing items are work area, release fuel pressure before disconnecting disassembly.
After disconnecting pipes, plug openings stop fuel leakage, when instructed to use SST, use specified tools, exercise maximum care to avoid damage to mating sliding surfaces, cover openings of engine system with tape or equivalent, if necessary, to seal out foreign materials.
Mark and arrange disassembly parts in an organized way for easy troubleshooting re-assembly, when loosening nuts and bolts, as a basic rule, start with the one furthest outside, then one diagonally, precautions for Inspection, Repair Replacement, before repairing or replacing, thoroughly inspect parts.
Use torque wrench to tighten bolts nuts specification, when tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with, ones in center, then ones on inside and outside diagonally in this order, replace with new gasket, packing, oil seal O-ring.
Dowel pins are used for several parts alignment, make sure that dowel pins are installed original position, thoroughly wash, clean, and air-blow each part, avoid damaging sliding or mating surfaces.
Before assembly, oil sliding surfaces well, release air within route when refilling after draining engine coolant, after repairing, start engine and increase engine speed to check engine coolant, fuel, engine oil, use angle wrench [SST: KV10112100 (BT8653-A)] for the final tightening of following engine parts.
Crankshaft pulley bolt (No angle wrench is required as bolt flange is provided with notches angle tightening), the torque value for these parts are preliminary step, ensure thread and seat surfaces are clean and coated with engine oil.
Nissan Models